OPERATING INSTRUCTIONS cont.
GETTING TO KNOW YOUR STICK VAC
Motor Thermostat
IMPORTANT: This unit is equipped with a motor protective thermostat. If for some reason the vacuum cleaner should overheat, the thermostat will automatically turn the unit off. Should this occur:
•Push the On/Off button once.
•Disconnect the plug from the power source.
•Check the source of overheating problem. (i.e. clogged hose or filter)
•If clogged hose or filter is found, unclog the hose and replace the filters.
•Wait at least 45 minutes before attempting to reuse the vacuum.
•After unit has cooled down for
45 minutes, plug in the cleaner and push the On/Off button. The vacuum should start again.
•If the vacuum still does not start, contact customer service at
21
TROUBLE SHOOTING GUIDE
PROBLEM |
| POSSIBLE REASON | POSSIBLE SOLUTION | ||
|
|
|
|
| |
| 1. | Power cord not firmly plugged into | 1. | Plug unit in firmly. | |
| 2. | Check fuse or breaker. Replace | |||
VACUUM WILL |
| outlet. |
| fuse/reset breaker. | |
2. | No power in wall outlet. | 3. | Call | ||
NOT OPERATE | |||||
3. | Needs servicing. | 4. | Turn the unit off and unplug from | ||
| |||||
| 4. | Thermostat has tripped. |
| outlet. Allow unit to cool down, | |
|
|
|
| then restart. | |
|
|
|
|
| |
| 1. | Dust cup is full. | 1. | Empty and clean dust cup. | |
VACUUM WILL | 2. | Turn unit off and unplug from | |||
2. | Unit clogged. |
| wall outlet. Remove Dust Cup | ||
NOT | 3. | HEPA Filter needs cleaning or |
| Filter and check for object(s) in | |
SUCTION POWER |
| replacing. |
| air duct and remove. | |
IS WEAK | 4. | Debris screen needs cleaning. | 3. | Clean or replace HEPA Filter. | |
| 5. | Filters need cleaning. | 4. | Clean debris screen. | |
|
|
| 5. | Clean filters. | |
|
|
|
|
| |
TURBO BRUSH | 1. | Dust cup is full. | 1. | Empty dust cup. | |
2. | Rotating brush or elbow is | ||||
2. | Clear obstructions. | ||||
DOES NOT |
| obstructed. | |||
| 3. | Call | |||
ROTATE OR | 3. | Belt is broken. | |||
4. | Clear obstruction. | ||||
ROTATES | 4. | Hose obstructed. | |||
5. | Clean debris screen. | ||||
SLOWLY | 5. | Debris screen is clogged. | |||
6. | Clean filters. | ||||
| 6. | Filters need cleaning. | |||
|
|
| |||
|
|
|
|
| |
DUST ESCAPING | 1. | Dust cup is full. | 1. | Empty and clean dust cup. | |
FROM VACUUM | 2. | Dust Cup is not installed correctly. | 2. | Review Dust Cup instructions. | |
|
|
|
|
| |
VACUUM, HOSE |
|
| 1. | Remove hose and/or brushes. | |
1. | Hose clogged. |
| Remove obstruction from hose | ||
OR BRUSHES |
| ||||
2. | Dust cup is full. |
| and /or brush. | ||
WILL NOT |
| ||||
|
| 2. | Empty and clean dust cup. | ||
|
|
| |||
|
|
|
|
| |
9
1. Hand Grip
2. Telescopic Tube
3. Locking Button
4. Flexible Hose
5. Dust Cup Release Button 1
6. Dust Cup Handle
7. Dust Cup (Container)
8. Main Unit
9.
10. Exhaust Filter Cover
11. On/Off Switch
12. Power Cord
13. Floor Brush Release Button
14. Floor Brush
15. Crevice Tool
16. Dusting Brush
17. Telescopic Tube Release Button
18. Dust Cup Release Button 2
19. Cord Hook Release
20. Hose Connector
21. Air Driven Turbo Brush
22. Shoulder Strap (not shown)
Technical Specifications
Voltage: | 120V., 60Hz. |
Power: | 10 Amps |
*Illustration may differ from actual product.
2
