Fantom Vacuum PT180H Rewinding the Spool with Line, Servicing of a DOUBLE-INSULATED Appliance

SAFETY & WARNING INSTRUCTIONS

OPERATING INSTRUCTIONS

34.Maintain the grass trimmer with care. Use only manufacturer’s replacement parts. Follow instructions for changing trimming line. Keep handles dry, clean and free from oil and grease. Always use a clean cloth when cleaning.

35.This appliance is double insulated to protect you from electrical shock.

36.Store the unit in a dry place either locked up or in a high shelf out of the reach of children to prevent unauthorized use or damage.

37.NEVER douse or squirt the unit with water or any other liquid. Keep handles dry, clean and free from debris. Clean after every use. See cleaning and storage section for further instructions.

38.Do NOT operate this unit in explosive atmospheres, such as in the presence of flammable liquids, gases or dust.

39.Maintain grass trimmer with care. Keep grass trimmer clean for best performance and to reduce the risk of injury.

40.When operating the grass trimmer, keep the extension cord behind the grass trimmer.

41.If the grass trimmer starts to vibrate abnormally, turn the unit off, remove the extension plug from the unit and allow the moving parts to stop rotating. Then inspect the grass trimmer for any damage or loose parts.

WARNING

SERVICING OF A DOUBLE-INSULATED APPLIANCE.

In a double-insulated product, two systems of insulation are provided instead of grounding. No grounding means are provided for a double-insulated product, nor should grounding means be added to the product. Servicing a double-insulated product requires extreme care and knowledge of the system and should be done only by qualified service personnel. Replacement parts for a double- insulated product must be identical to the original parts. A double-insulated product is marked with the words

" double Insulation" or "Double

Insulated". Product may also be marked with symbol shown.

42.Use the grass trimmer ONLY in the upright position, with the cutting line near the ground as shown in the instruction manual. Never use the grass trimmer in any other position.

43.Do not work on a steep slope, always be sure of your footing. Please note that freshly cut grass is damp and slippery.

44.Use only the trimmer line supplied by the manufacturer. Never use metal cutting or fishing line.

45.After extending new trimmer line, return the unit to its normal operating position before turning the unit back on.

46.Never use the grass trimmer if the grass is wet.

47.Use only FANTOM replacement parts.

48.Use specified trimmer spool. Make sure that the spool is properly installed and all parts are securely fastened.

49.Check damaged parts – Before further use of the unit, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other condition that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless indicated elsewhere in this manual.

WARNING: Trimmer line throws objects violently. You and others can

be seriously injured. Wear safety glasses, boots and leg protection. Keep body parts clear of rotating line.

WARNING: Disconnect unit from power source before performing maintenance or when changing the trimmer

line.

WARNING: All electrical repairs to this unit, including housing, motor, etc.,

must be diagnosed by qualified service personnel. Replacement parts for a double insulated appliance must be recommended by the manufacturer.

Rewinding the Spool with Line

If you wish to rewind the spool yourself, replace with a nylon cutting line that is 0.05” diameter and 30-feet long. Use of heavier lines could overload and damage your grass trimmer.

To rewind trimmer line onto the spool:

1.Remove the empty spool from the grass trimmer following the instructions on page 7.

2.Cut the new nylon cutting line to the exact length.

3.Orient the two (2) holes on the bottom of the hub with Slot “A” on the line retainer. (Fig. 12)

Align

Slot “A”

Fig. 12

4.Feed one end of the cutting line into the hole on the right side first.

(Fig. 13) Take out about 4-inches and pull it until it comes out of Slot “B”. (Fig. 14)

Fig. 13

Fig. 14 Slot “B”

5.Bend ½-inch of the other end of the cutting line and feed through until it comes out of slot “A”. (Fig. 15) Pull out about 4-inches.

Slot “A” Fig. 15

6.Pull the ends of the cutting line alternately until you have it evenly distributed through the openings. (Fig. 16)

Fig. 16

7.When you have completely pulled the cutting line through the spool, hold the spool in your hand so that your thumb and fingers can be used as guides when winding the cutting line. Rotate the hub counter-clockwise until the line is wound around the spool. (Fig. 17) Make sure that you leave about 6-inches of the line on each side for the spool to function properly.

Fig. 17

8.Replace the spool back into the unit following the instructions on page 7.

8

3