OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
Assembly of Blower
WARNING: Remove the plug from the power source before
assembly of leaf blower. This will help prevent accidental starting of the unit which could result in serious injury.
CAUTION: The impeller rotates for a few seconds after you turn off the
blower and will cause injury. WAIT until all parts stop moving.
WARNING: Do not remove the bottom inlet cover when the motor is
running or when the unit is plugged into power outlet.
NOTE: Instructions must be followed in order.
1.Ensure unit is unplugged and all parts have stopped moving.
2.Slide blower tube onto the blower outlet. (Fig. 1)
Fig. 1
NOTE: You must install the blower tube before installing the inlet cover because the inlet cover hooks onto the blower tube.
3.Attach inlet cover onto hook on blower tube. (Fig. 2)
Fig. 2
Hook on blower tube
4.Lift handle to lock inlet cover into place at rear of motor. (Fig.3)
IMPORTANT: The blower will not run unless the bottom inlet cover is locked in place.
Assembly of Vacuum
WARNING: Remove the plug from the power source before assembly of vacuum. This will help prevent accidental
starting of the unit which could result in serious injury.
WARNING: Do not remove the bottom inlet cover when the motor is
running or when the unit is plugged into power outlet
CAUTION: The impeller
rotates for a few seconds after you turn off the blower and will cause injury. WAIT until all parts stop moving.
To assemble vacuum tubes instructions must be followed in order:
1.Align tabs on upper and lower vacuum tube ensuring that the guide is also aligned. Forcefully slide lower vacuum tube onto upper vacuum tube until upper tube is at end of lower tube. Once in place these tubes are permanently attached.
Fig. 4
Tab on Tube
Fig. 5
2.Push easy grip handle into place on upper tube. (Fig. 5)
NOTE: This is a permanently assembly, there is no reason to take apart after assembled.
3.Align notch on easy grip handle with tabs on upper tube.
Attaching Vacuum to Motor
WARNING: Remove the plug from the power source before assembly of leaf blower. This will help prevent accidental starting of the unit
which could result in serious injury.
Attach collector debris bag to Motor when you wish to use unit as a vacuum.
Once the tubes and easy grip handle have been attached you can proceed to attach bag to blower outlet.
1.Loosen velcro strap on debris collector bag.
2.Place narrow end of adapter into debris collector bag. There is enough space for collar of bag to sit above ridge created for bag cuff.
3.Pull velcro strap to tighten cuff on adapter. Ensure that bag is properly attached to avoid debris from being thrown out of opening. (Fig. 6)
| Ridge for |
Fig. 6 | bag |
|
4.Align locking tab with motor’s locking tab holder and slide onto blower outlet until you hear a click . (Fig 7)
Fig. 7
NOTE: The strap on the bag is adjustable for comfort of use. It is suggested that you place strap across your chest. Attach Vacuum to Motor when you wish to use unit as a vacuum.
NOTE: Only use vacuum to pick up small dry debris such as: grass clippings, dry leaves, or small twigs.
DO NOT vacuum up glass, pebbles, gravel, or large sticks.
NOTE: Bag adapter must be in position before vacuum tubes can be attached.
5.Angle motor to allow hook on bag adapter to securely hook onto last bar of easy grip handle.
6.Lift easy grip handle to secure locking tab in place. (Fig. 8)
Locking tab to easy grip handle
Fig. 8
Hook bag onto
Last bar of easy grip handle
Converting Your Unit From Vacuum to Blower
1.Unplug unit and ensure all parts stop moving.
2.Press on locking tab near handle to remove easy grip handle from motor. Angle motor to release hook from locking bar. (Fig. 9)
Fig. 9
3.Press on locking tab to remove bag adapter from unit. (Fig. 10)
Fig. 3
6
IMPORTANT: The vacuum will not run unless the vacuum tube is locked in place.
Fig.10
7
