Fellowes 49C Basic Shredding Operation, Oiling Shredder, Troubleshooting, Continuous operation

BASIC SHREDDING OPERATION

Continuous operation:

6Q
UP

NJOVUFT
NBYJNVN

NOTE: Shredder runs briefly after each pass to clear entry. Continuous operation beyond 5 minutes will trigger a

30-minute cool down period.

PAPER/CARD
1	2	3	4

Plug in and put	Set to Auto-On (	)	Feed paper/card	When finished
disconnect power			straight into paper	shredding set to
switch in ON (I) position			entry and release	OFF ( )
Safety Lock prevents accidental operation.			To set, wait for shredding to stop, push black button down and slide towards front of shredder.

To unlock push black button down and slide toward back of shredder. For greater safety, always unplug shredder after use.

PRODUCT MAINTENANCE

OILING SHREDDER

All cross-cut shredders require oil for peak performance. If not oiled, a machine may experience diminished sheet capacity, intrusive noise when shredding and could ultimately stop running. To avoid these problems, we recommend you oil your shredder each time you empty your waste bin.

FOLLOW OILING PROCEDURE BELOW AND REPEAT TWICE

1 2 3

Set to Off ( )	*Apply oil	Set to Reverse (	)
	across entry	for 2-3 seconds

*Only use a non-aerosol vegetable oil in long nozzle container such as Fellowes 35250

TROUBLESHOOTING

Overheat Indicator: When the Overheat Indicator is illuminated, the shredder has exceeded its maximum operating temperature and needs to cool down. This indicator will remain illuminated and the shredder will not operate for the duration of the recovery time. See Basic Shredding Operation for more information about the continuous operation and recovery time for this shredder.

PAPER JAM
1	2	3	4	5	6

Set to Reverse		Alternate slowly back and forth	Set to Off ( )	Gently pull uncut	Set to Auto-On (	)
(	) for 2-3		and unplug	paper from paper	and resume shredding
seconds				entry. Plug in.

LIMITED PRODUCT WARRANTY

Limited Warranty: Fellowes, Inc. (“Fellowes”) warrants the parts of the machine to be free of defects in material and workmanship and provides service and support for 1 year from the date of purchase by the original consumer. Fellowes warrants the cutting blades of the machine to be free from defects in material and workmanship for 3 years from the date of purchase by the original consumer. If any part is found to be defective during the warranty period, your sole and exclusive remedy will be repair or replacement, at Fellowes’ option and expense, of the defective part. This warranty does not apply in cases of abuse, mishandling, failure to comply with product usage standards, shredder operation using an improper power supply (other than listed on the label), or unauthorized repair. Fellowes reserves the right to charge the consumers for any additional costs

incurred by Fellowes to provide parts or services outside of the country where the shredder is initially

TPME
CZ
BO
BVUIPSJ[FE
SFTFMMFS
"/:
*.1-*&%
8"33"/5:
*/$-6%*/(
5)"5
0'
.&3$)"/5"#*-*5:

03
'*5/&44
'03
"
1"35*$6-"3
163104&
*4
)&3&#:
-*.*5&%
*/
%63"5*0/
50
5)&
"113013*"5&
WARRANTY PERIOD SET FORTH ABOVE. In no event shall Fellowes be liable for any consequential or incidental damages attributable to this product. This warranty gives you specific legal rights. The duration, terms, and conditions of this warranty are valid worldwide, except where different limitations, restrictions, or conditions may be required by local law. For more details or to obtain service under this warranty, please contact us or your dealer.

3