Fellowes C14 Product Profile, Set-Up, Operation, Important Safety Instructions, Control Switches

Product Profile

This product is built to shred paper, staples, small paper clips, credit cards, CDs, and DVDs (CDs and DVDs in designated slot). It is not built to shred transparencies, adhesive labels, newspaper, cardboard, large paper clips, or plastic (other than items noted above). Attempting to shred items not intended for this shredder may cause damage.

	Confetti-cut
	(C14)
Sheet capacity*	15 sheets
CD capacity	1
Paper shred size	5/32" x 1 1/2" (3.9 x 38 mm)

Set-Up

•Pull waste basket drawer (A) completely out of cabinet.

•Put waste bag in basket (sample bags provided). Allow edges to overhang. Contact Fellowes to order more bags. (Part #36053).

•Slide waste basket drawer (A) into cabinet. The shredder will not operate if drawer is not pushed all the way into cabinet.

•Casters have been added for your convenience.

•Plug power cord into a convenient outlet.

Operation

Control Switches

Maximum paper width	9" (230 mm)
Recommended daily capacity	100-200 shredding passes
Maximum running time	25 minutes
Automatic cool-down period	40 minutes
Voltage	120V-60Hz 6.0A

*Based on 20 lb., 8-1/2" x 11" paper with shredder operating at rated voltage; heavier paper, high humidity, or other than rated voltage may reduce sheet capacity.

IMPORTANT SAFETY INSTRUCTIONS

F

E

H

Control Switch (E)

IAUTOMATIC Turns on the auto- matic-start sensor and the green Ready light.

O OFF	R REVERSE
Turns off the auto-	Runs shredder in
matic-start sensor	reverse mode.
and the green	Press and hold to
Ready light.	activate.

READ ALL INSTRUCTIONS BEFORE USING

While setting up shredder

•Check shredder for damage or defects; some paper particles in the basket are normal due to product testing and does not indicate a defect.

•If the cord is damaged do not replace cord or use the machine. Return machine for a replacement.

•Avoid touching exposed blades on underside of confetti-cut shredder head.

•Plug power cord in an outlet that can easily be reached. The plug is the primary electrical disconnect.

•Make sure the electrical rating listed on the serial label (located inside, just below top of shredder) matches the available electric power.

•Do not place shredder near or over a heat or water source.

While operating shredder

• Keep hands and hanging objects (jewelry, ties, loose clothing, long hair, etc.) away from paper entry.

• Keep children and pets away from the shredder.

When not in use

•Always turn off and unplug shredder.

•Unplug before emptying basket.

•Do not open shredder head: Danger of electric shock. Opening shredder head will void the warranty.

NOTE: Do not use flammable synthetic oil, petroleum-based products or aerosols of any kind on or near product at any time.

3

I	J
	Troubleshooting Lights
Ready Light (F)	Basket Ajar (H)	Paper Jam (I)	Overheat Light
(Green)	Waste basket	Shredder is	(J)
Shredder is in	drawer is open.	jammed (e.g.,	Shredder has
automatic start	Basket Full (H)	too much paper	overheated (e.g.
mode.		fed at one time).	shredder has been
	Waste basket is

full or paper has	used for more
	than 25 minutes).
collected under
cutting cylinders.

For convenience and energy savings, your shredder is equipped with an automatic-start sensor (K). This means that when the control switch (E) is in the automatic [I] position, the shredder will start running when paper is fed into it. The shredder stops a few seconds after the paper has passed through.

CAUTION: The automatic-start sensor cannot tell the difference between paper and other objects. This feature can also be a hazard. Always turn off the shredder when it is not in use. Unplug the shredder if it will not be used for an extended period.

To shred

•Press control switch (E) to automatic [I] position. Green ready light (F) should turn on.

PAPER

•Feed paper straight into entry (C), releasing when shredder begins shredding; see Product Profile for limits on paper width, shreddable items, sheet capacity, etc.

•Shred no more than 25 minutes; shredding longer will cause shredder to turn itself off for 40 minutes to cool down.

•Press control switch to off [O] position after cutting has stopped.

4