See safety instructions below

Shredder head

Paper entry

Mounting for paper-tray

GLISH

Models HS-800

Disconnect power switch (red)

Control panel

Auto On/Off (green)

Forward (toggle)

OPERATION

Refer to separate setup instructions for proper assembly. Disconnect power switch must be in ON position to operate shredder. Insert waste bag (Fellowes

#36056) for easy disposal.

Press Auto-On/Off

Feed into paper entry

Set to Off

 

 

 

and release

 

TROUBLESHOOTING

Paper jam: Set to Off (O) and empty bin. Replace bin, close door, and follow any or all of the below procedures.

Indicator lights:

Form feed paper-tray Mounts on front or back of shredder.

Door

Jam (red)

Reverse

Door Open (yellow) Bin Full (yellow)

Shredder will

 

 

automatically

 

 

Reverse out

 

 

paper

Remove all uncut

Press Forward for 5 seconds to clear

 

 

paper from entry

cutters. Press Forward button again

to resume Auto start

After a jam, all lights on machine go off and machine doesn’t go back on. Open door and reset circuit breaker.

tightly closed (yellow) Paper Jam (red)

Remove and empty bin (yellow)

Circuit breaker

Bin

MAINTENANCE

Lubricate machine before starting to shred, after every 10 minutes of continuous shreddering,

Follow oiling procedure below and repeat twice.

CAPABILITIES

Will shred: Paper

Maximum:

or immediately if:

Capacity decreases

Motor sounds different, or shredder stops running

Press Forward

 

ry

Press Forward

Shred one sheet

Press Reverse button

button

across ent

button

 

 

Will not shred: Adhesive labels, transparencies, newspaper, credit cards, cardboard, paper clips, staples, laminates or plastic other than noted above

Paper shred size:

 

High Security Cross-Cut

1/25” x 3/16” (1 x 4.7mm)

Sheets per pass

8*

Sheets per day

5,000

Paper entry width

16” (400 mm)

*20lbs., 8.5”x11” paper at 120v, 60Hz, 14 Amps; heavier paper, humidity or other than rated voltage may reduce capacity. Recommended daily usage rates: 5,000 sheets per day.

*Only use a non-aerosol vegetable oil in long nozzle container such as Fellowes #35250

CLEANING AUTO-START INFRARED SENSORS

Paper detection sensors are designed for maintenance free operation. However, on rare occasions the sensors may become blocked by paper dust causing the motor to run even if there is no paper present (Note: two paper detection sensors are located in the center of the paper entry).

IMPORTANT SAFETY INSTRUCTIONS — Read Before Using!

TO CLEAN THE SENSORS

1

 

2

 

3

Keep hands away from paper entry. Always set to

Off () or unplug when not in use.

• Keep foreign objects – gloves, jewelry, clothing, hair, etc.– away from shredder openings. If object enters top opening, switch to Reverse () to back out object.

• Never use aerosol, petroleum-based or other flammable products on or near shredder. Do not use canned air on shredder.

Do not use if damaged or defective. Do not open shredder head. Do not place near or over heat or water source.

• 8 sheets per pass to avoid jams.

Locate Auto-start infared

Dip cotton swab in rubbing

Using cotton swab, wipe away

sensor.

alcohol.

any contamination from the

 

 

paper sensors.

WARRANTY

Avoid touching exposed blades under High Security Cross-Cut shredder head.

The grounded socket-outlet shall be installed near the equipment and shall be easily accessible.

Make sure shredder gets sufficient ventilation (ventilating grills must be kept free).

LIMITED WARRANTY Fellowes, Inc. (“Fellowes”) warrants the cutting blades of the machine to be free from defects in material and workmanship for 5 years from the date of purchase by the original consumer. Fellowes warrants all other parts of the machine to be free of defects in material and workmanship for 2 year from the date of purchase by the original consumer. If any part is found to be defective during the warranty period, your sole and exclusive remedy will be repair or replacement, at Fellowes’ option and expense, of the defective part.

This warranty does not apply in cases of abuse, mishandling, or unauthorized repair. ANY IMPLIED WARRANTY, INCLUDING THAT OF MERCHANTABILITY OR

FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED IN DURATION TO THE APPROPRIATE WARRANTY PERIOD SET FORTH ABOVE. In no event shall Fellowes be liable for any consequential or incidental damages attributable to this product.

This warranty gives you specific legal rights. The duration, terms, and conditions of this warranty are valid worldwide, except where different limitations, restrictions, or conditions may be required by local law.

For more details or to obtain service under this warranty, please contact us or your dealer.

2

3

Page 2
Image 2
Fellowes HS-800 manual Operation, Troubleshooting, Capabilities, Cleaning AUTO-START Infrared Sensors, Warranty

HS-800 specifications

The Fellowes HS-800 is an advanced paper shredder designed for home or small office use, combining efficiency, security, and user-friendly features. This model stands out in the crowded market of shredders, particularly for its powerful performance and robust build quality.

One of the main features of the HS-800 is its cross-cut shredding capability. It is capable of shredding paper into tiny particles, ensuring that confidential documents are rendered unreadable. This shredding style provides a higher level of security compared to strip-cut shredders, making it ideal for organizations and individuals keen on protecting sensitive information.

The HS-800 has a robust motor that can handle up to 15 sheets of paper at once. This high sheet capacity significantly boosts productivity, allowing users to shred larger amounts of documents without frequent interruptions. Furthermore, the shredder can also handle credit cards, staples, and paper clips, adding versatility to its functionality.

Technology-wise, the Fellowes HS-800 incorporates a cooling technology that helps prevent overheating during longer shredding sessions, prolonging the lifespan of the machine. The device features an intelligent safety lock that ensures the shredder only operates when the waste bin is securely closed, reducing the risk of accidents.

The shredder is designed with an easy-to-empty waste bin that can hold a significant volume of shredded paper. This feature minimizes the hassle of constant emptying. The transparent window allows users to see when the bin is nearing capacity without opening it, ensuring a seamless shredding experience.

In addition to these features, the HS-800 boasts low noise operation, making it suitable for office environments where noise levels need to be managed. Its compact design allows it to fit under desks or in small spaces without sacrificing performance.

Overall, the Fellowes HS-800 is a well-rounded shredder that excels in power and convenience. With its high security, user-focused technologies, and durable construction, it is an excellent choice for anyone in need of reliable document disposal solutions. Whether for personal use or in a small business setting, the HS-800 meets the demands of today’s data security landscape.