English, Set Up, To Test SafeSense Technology, Operation

Shredder head

SafeSense® Technology

Indicator lights (red) Paper Jam

Door Open Overheated

Window

Sheet capacity gauge Sheet capacity icon

ENGLISH

Model PS-10Cs

Disconnect power switch

Card entry

SafeSense® override switch

Active

Not active

SafeSense® (yellow)

Standby (green)

OPERATION

Continuous operation:

8-10 minutes maximum

NOTE: Shredder runs briefly after each pass to clear entry. Continuous operation beyond 8-10 minutes will trigger

20-minute cool down period.

Set to Off (O) and plug in

PAPER

Check paper amount	Press Auto-On (I)	Feed into paper entry
		and release

CARD

Press Auto-On (I)	Hold card	Feed into card entry
	at edge	and release

Set to Off (O) and unplug

See safety instructions below

Pull-out bin Paper entry

Control switch

Auto-On (I)

Off (O)

Reverse (R)

TROUBLESHOOTING

Paper jam: Set to Off (O) and empty bin. Replace bin, close door and follow any or all of the below procedures.	Indicator lights:

	Yellow - SafeSense® active
	Yellow flashing - SafeSense® not active

Breakthrough Safety Technology! SafeSense® stops shredding when hands are too close to the opening.

SET UP

Disconnect Power Switch
must be in ON position to	A	B
operate shredder.	A	B
Insert waste bag (Fellowes
#36052) for easy disposal.

— To Test SafeSense® Technology

Press Auto-On ( I )

Touch test area

Sensor lights up

					Make sure bin is pushed in
Press and hold	Alternate slowly back and forth	Set to Off (O)	Gently pull uncut paper	Press and hold	Wait 20 minutes for motor to cool down
Reverse (R)		and unplug	from paper entry. Plug in.	Reverse (R)	Wait 20 minutes for motor to cool down
Reverse (R)		and unplug	from paper entry. Plug in.	Reverse (R)

ATTENTION: If the SafeSense® light remains on, you must engage the Override Switch in order to perform steps above. Once the jam is cleared, reset the SafeSense® feature.

(See SafeSense® instructions below.)

CAPABILITIES

Will shred: Paper, credit cards, staples and small paper clips

Will not shred: Continuous forms, adhesive labels, transparencies, newspaper, cardboard, large paper clips, laminates or plastic other than noted above

Paper shred size:
Cross-Cut	5/32 inches x 1-1/2 inches (3.9mm x 38mm)

Maximum:
Sheets per pass (Cross-Cut)	.............................................................................. 10*
Cards per pass	1*
Paper width	9 inches/229mm
Continuous operation	8-10 minutes

*20lb., 8.5 inches x11 inches (75g) paper at 120v, 60 Hz, 4.0Amps; heavier paper,

humidity or other. than rated voltage may reduce capacity. Recommended daily usage rates: 25-50 paper passes; 25 cards.

SafeSense® paper jam: If the SafeSense® feature activates (SafeSense® light remains on) to cause the user to think the		Sensor light illuminated–paper jammed

shredder has jammed when it has not, use the	Override Switch to deactivate the SafeSense® feature and clear the
paper. Warning – when switch is in override position, the SafeSense® light will flash and the SafeSense® feature will NOT
function. Once the paper is cleared, reset the SafeSense® feature.		SafeSense® override switch
		SafeSense® override switch
		Active	Not active

MAINTENANCE

IMPORTANT SAFETY INSTRUCTIONS — Read Before Using!

Run regularly in reverse for Follow oiling procedure below and repeat twice. one minute

Oil when bin is full, or immediately, if:

•Keep away from children and pets. Keep hands away from paper entry. Always set to off or unplug when not in use.

• Keep foreign objects – gloves, jewelry, clothing, hair,

• Never use aerosol, petroleum based or other flammable products on or near shredder. Do not use canned air on shredder.

•Do not use if damaged or defective. Do not open shredder head.

Do not place near or over heat or water source.

•Capacity decreases

•Motor sounds different, or

Shredder stops running

Set to Off (O)	*Apply oil	Press Auto-On (I)	Shred one sheet	Press and hold
	across entry			Reverse (R)
	*Only use a non-aerosol vegetable oil in long nozzle container such as Fellowes 35250			2-3 seconds

etc. – away from shredder openings. If object enters top opening, switch to Reverse (R) to back out object.

•Avoid touching exposed blades under Cross-Cut shredder head.

•Use only designated entry for cards.

• 10 sheets per pass to avoid jams.

•The grounded socket-outlet shall be installed near the equipment and shall be easily accessible.

WARRANTY

LIMITED WARRANTY Fellowes, Inc. (“Fellowes”) warrants the cutting blades of the machine to be free from defects in material and workmanship for 5 years from the date of purchase by the original consumer. Fellowes warrants all other parts of the machine to be free of defects in material and workmanship for 1 year from the date of purchase by the original consumer. If any part is found to be defective during the warranty period, your sole and exclusive remedy will be repair or replacement, at Fellowes’ option and expense, of the defective part.

HEREBY LIMITED IN DURATION TO THE APPROPRIATE WARRANTY PERIOD SET FORTH ABOVE. In no event shall Fellowes be liable for any consequential or incidental damages attributable to this product.

This warranty gives you specific legal rights. The duration, terms, and conditions of this warranty are valid worldwide, except where different limitations, restrictions, or conditions may be required by local law.

This warranty does not apply in cases of abuse, mishandling, or unauthorized repair. ANY IMPLIED WARRANTY, INCLUDING THAT OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS

For more details or to obtain service under this warranty, please contact us or your dealer.

Fellowes English, Set Up, To Test SafeSense Technology, Capabilities, Model PS-10Cs, Operation

Models: PS-10Cs