Fender 810 - page 6

wwwwww

ffeennddeerr..ccoomm

✧

wwwwww

..mmrrggeeaarrhheeaadd..nneett

FFee

eenn

nndd

ddee

eerr

rr®88

8811

1100

PPrr

rroo

oo™™

™™

LLoo

oouu

uudd

ddss

sspp

ppee

eeaa

aakk

kkee

eerr

EEnn

nncc

ccll

lloo

ooss

ssuu

uurr

rree

Your new 810 Pro™ Bass Loudspeaker Enclosure is

constructed from 3/4" (1.9 cm) 7-ply Birch/Maple

Plywood and is capable of handling 600 Watts of con-

tinuous power. The 810 Pro™ features eight 10"

(25.4 cm) speakers with 44 oz (1.25 kg) magnets and is

designed for use with a Fender®Bassman®1200,

Bassman®300, Bassman®400 Head or other profes-

sional quality bass amplifier. Please read these instruc-

tions and the instructions that came with your amplifier

before making connections. Follow all equipment cau-

tion and safety labeling.

SPEAKER CONNECTIONS

Use 16 gauge (or heavier) speaker cable with one of the

three types of input connections on your 810 Pro™:

A) Phone jacks with a standard 1/4" plug

B) Binding posts with dual “banana” plug or

stripped wires

C) Speakon®connector with Speakon®plug

Multiple 810 Pro™ cabinets can be linked as illustrated,

when additional output is needed. Note: Follow the

speaker impedance load guidelines set by the manufac-

turer of your amplifier to avoid damage to your equip-

ment.

HORN TWEETER

The horn tweeter is protected from power-overload

damage by an incandescent lamp. If the horn tweeter

stops responding, replace the lamp as you would a

blown fuse. The lamp and a spare (reorder P/N

051857) are located on the circuit board on the inside

of the input jack panel.

Lamp Replacement:

1) Remove the 4 screws from the input jack

panel corners.

2) Pull the panel out, then up.

3) Use a small flathead screwdriver to remove the

blown lamp which is visible through a cutout

in the circuit board.

4) Remove the spare lamp stowed on the side of

the circuit board and install it where the blown

lamp was located.

5) Install the input jack plate in the reverse order

of removal.

SPECIFICATIONS

PART NUMBER: 2217200000

DRIVERS: Eight 10" (25.4 cm) Fender®

Special Design Cast Frame

Woofers

2" (5.1 cm) Voice Coil, 44 oz

(1.25 kg) Magnet

One Horn Tweeter

1" (2.5 cm) Voice Coil, 8 oz

(0.23 kg) Magnet

CABINET: 3/4" (1.9 cm) 7-ply

Birch/Maple Plywood

SENSITIVITY: 94 dB, 1 Watt - 1 Meter

POWER HANDLING: 600 Watts, Continuous

1200 Watts, Program

IMPEDANCE:4Ω

CONNECTIONS: Dual, Parallel Wired, 1/4”

High Current Input Jacks,

Binding Posts and

Speakon®Connector

ENCLOSURE VOLUME: VB= 7.9 ft3 (224 l)

DIMENSIONS:

Height: 48 in (121.9 cm)

Width: 26 in (66.0 cm)

Depth: 17 in (43.2 cm)

WEIGHT: 157 lb (71.4 kg)

Product specifications are subject to change without notice.

A PRODUCT OF:

FENDER MUSICAL INSTRUMENTS CORP.

CORONA, CA USA

Fender

is a registered trademark of FMIC,

Speakon

is a registered trademark of Neutrik.