Ferris Hydraulic Pump Drive Belt Replacement | Mower Belt Diagram Guide

Troubleshooting, Adjustment & Service

HYDRAULIC PUMP DRIVE BELT REPLACEMENT

1.Park the tractor on a smooth, level surface such as a concrete floor. Disengage the PTO, engage the parking brake, turn off the engine, and remove the ignition key.

2.Remove the PTO drive belt (see MOWER BELT REPLACEMENT for removal instructions).

3.Remove the hardware that secures the clutch anchor pad to the PTO clutch.

4.Loosen the nut towards the front of the machine on the spring anchor hook (G, Figure 43) to release the majority of the belt tension. Use caution and remove the nut to completely release the tension.

5.Remove the old belt and replace it with a new one. Make sure the V-side of the belt runs in the grooves of the crankshaft pulley and pump pulleys (B & C).

6.Reinstall the anchor hook (G) into the anchor tab and loosely fasten the nut. Adjust the anchor hook until a measurement of 8-3/8” (21,2 cm) is achieved from the outside if the spring hooks. Tighten nut.

7.Reinstall the clutch anchor pad to the PTO clutch and secure with the hardware previously removed.

8.Reinstall the PTO drive belt.

	B
	D	A
8 3/8”	E
(21,2 cm)
C		C
C
	F	G

Figure 43. Hydraulic Pump Drive Belt

Replacement

A.Pump Drive Belt

B.Crankshaft Pulley

C.Pump Pulley

D.Idler Pulley

E.Idler Arm

F.Spring

G.Spring Anchor Hook

Troubleshooting

44	www.ferrisindustries.com

Image 46

Ferris Industries 5900629, 5901170, 5900625, 5900624, 5900619 manual Hydraulic Pump Drive Belt Replacement

Contents

Model Number DescriptionFerris Industries Date Purchased Table of Contents Operating Safety Slope Operation Roll Bar Use Fuel and Maintenance Training OperationPreparation Children Slope OperationTowed Equipment RIDE-ON Units Emissions Maintenance and Storage Service and MaintenanceSafe Handling of Gasoline Roll BAR Instructions Operational Warnings Inspection and Maintenance of the Roll BAR Seat Belt Identification Numbers Identification Safety Decals Safety Decals North American Safety Icons Safety Interlock SystemOperational Safety Checks AIR Cooled Models only Seat Adjustment LeverIgnition Switch Control Functions Parking Brake PTO Power Take Off SwitchHour Meter / Maintenance Reminder Throttle Control Liquid Cooled Models only Water Temperature Gauge Checks Before Starting General Operating SafetyNever allow passengers to ride on the unit Stopping the Rider Starting the EnginePushing the Rider by Hand Forward Travel Practice Zero Turn Driving PracticeSmooth Travel Reverse Travel Practice Executing Turns Practice Turning Around a Corner Practice Turning In PlaceExecuting an End-Of-Row Zero Turn Turning Height of Grass MowingMowing Recommendations Tall Grass Requires Incremental Cutting Mowing Patterns When and How Often to MowMowing Methods Proper Broadcast Mowing Attaching a Trailer Proper Mulching To raise the roll bar Raise & Lower the Roll BARTo lower the roll bar Keep roll bar in the raised position and use seat belt Temporary Storage 30 Days Or Less StorageStarting After Long Term Storage Long Term Storage Longer Than 30 Days Engine Maintenance Safety ItemsRider Maintenance Before Every Spring Each 100 250 Fall Use Hours Fuel Filter Check Tire PressuresChecking / Adding Fuel Change OIL & Filter Air Cooled Models Check Hydraulic OIL LevelChange Hydraulic OIL Filter Liquid Cooled Models Check Engine Coolant Level Change Engine Coolant Clean Radiator & ScreenPressurized System Oil LubricationGrease Pivots Cleaning the Battery and Cables Air Cooled Models Battery MaintenanceCleaning the Battery and Cables Liquid Cooled Models Servicing the Mower Blades Removing the Blade Troubleshooting Warning Troubleshooting the Rider Troubleshooting the Mower Rider Troubleshooting Troubleshooting Common Cutting Problems Streaking Ground Speed Control Lever Adjustment Seat AdjustmentSpeed Balancing Adjustment Adjustment Linkage Rod Neutral AdjustmentRETURN-TO-NEUTRAL Adjustment RH side shown Parking Brake Adjustment Parking Brake Adjustment Brake Spring Adjustment Nut To adjust the spring pre-load Suspension AdjustmentTo adjust the upper mounting position Foot Pedal Adjustment Mowing Height AdjustmentTo adjust pedal position Inner Rod Deck Lift ROD Timing AdjustmentOuter Rod Deck Lift Spring Deck Leveling Adjustment4 Locations Hydraulic Pump Drive Belt Replacement Mower Belt Replacement Deck Charging a Completely Discharged Battery Battery ServiceChecking Battery Voltage Jump Starting With Auxiliary Booster Battery Make Certain Vehicles do not Touch This HOOK-UP for Negative Ground VehiclesJump Starting Chassis DimensionsEngine Transmissions Ferris Limited Warranty Tractor Belts and BladesMower Deck