SAFE USE & MAINTENANCE OF PROPANE GAS CYLINDERS

READ AND FOLLOW ALL WARNINGS PROVIDED WITH YOUR PROPANE GAS CYLINDER.

IMPORTANT FOR YOUR SAFETY

When operating this appliance with a Propane gas Cylinder these instructions and warnings MUST be observed.

FAILURE TO DO SO MAY RESULT IN A SERIOUS FIRE OR EXPLOSION.

CYLINDER AND CONNECTOR REQUIREMENTS AND

SPECIFICATIONS

a.Propane gas cylinders and valves must be maintained in good condition and must be relaced if there is visible damage to either the cylinder or valve.

b.This Barbecue, when used with a cylinder, should be connected to a standard 5 gallon (20lb.) Propane gas cylinder equipped with an OPD (Overfill Prevention Device). The OPD has been required on all cylinders sold since October 1,1998 to prevent overfilling.

c.Cylinder dimensions should be approximately 12 inches in diameter and 18 inches high. Cylinders must be constructed and marked in accordance with the specifications for Propane Gas Cylinders of the U.S. Department of Transportation (D.O.T) or the National Standard of Canada,CAN/ CSA-B339, Cylinders, Spheres and Tubes for Transportation of Dangerous Goods.

d.The cylinder must include a collar to protect the cylinder valve and the cylinder supply system must be arranged for vapor withdrawal.

e.The pressure regulator and hose assembly (Figure 3A,) supplied with this outdoor cooking gas appliance must be used. Original and replacement pressure regulator and hose assemblies must be those specified by the Robert H. Peterson Co. for connection with a cylinder connecting device identified as Type I by the Harmonized Standard ANSI Z 21.58 and CGA 1.6-M95-1995 with Addenda ANSI Z 21.58a -1998 and CGA 1.6a - M98.

f.The Propane gas cylinder valve must be equipped with a cylinder connection coupling device, described as Type I in the Harmonized ANSI standard defined in paragraph e. above. This device is commonly described as an Acme Thread Quick Coupler.

g.Your Propane Gas Cylinder may be equipped with a Type II Quick Disconnect (plug-in) Coupler (Figure 3B). An approved regulator /hose assembly for this type of coupling is available through your dealer from R.H. Peterson Co.

QUICK COUPLER OPERATION

To connect the Regulator/hose assembly to the LP gas cylinder valve fitting: Press the Hand Nut on the Regulator over the Acme thread fitting on the cylinder valve. Turn the Hand Nut clockwise to engage the threads and tighten until snug. The use of pliers or wrench should not be necessary.

To disconnect:- Turn the Hand Nut counter-clockwise until detached. (Figure 3a).

Important: Before using the Barbecue and after each time the cylinder is removed and reattached, check all connections for leaks. Turn off the Barbecue valves and open the main cylinder valve, then check connections with soapy water. Repair any leaks before lighting the Barbecue.

CAUTION: Always turn the Propane cylinder main valve off after each use and before moving the Barbecue and cylinder or disconnecting the coupling. This valve must remain closed while the appliance is not in use, even though the gas flow is stopped by a safety feature when the coupler is disconnected.

Carefully inspect the hose assembly each time before the gas is turned on. A cracked or frayed hose should be replaced immediately.

If the appliance is stored indoors, the cylinder must be disconnected and removed. Cylinders must be stored out of the reach of children and must not be stored in a building, garage or any other enclosed area.

FOR YOUR SAFETY

a.DO NOT store a spare Propane Gas cylinder under or near this appliance.

b.NEVER fill the cylinder beyond 80 percent full.

c.IF THE INFORMATION IN “A” AND “B” IS NOT

FOLLOWED EXACTLY, A FIRE CAUSING DEATH OR SERIOUS INJURY MAY OCCUR.

QCC TYPE I

 

 

CYLINDER VALVE

 

MAIN VALVE

(QUICK DISCONNECT COUPLER)

HANDWHEEL

 

 

BRASS COUPLING NUT

PRESSURE

UL

 

RELIEF VALVE

 

 

 

 

LIQUID LEVEL

 

 

INDICATOR

 

CYLINDER

(OPTIONAL)

HAND NUT

WITH

ACME THREAD

REGULATOR

VENT

HOSE

TYPE II

 

CYLINDER VALVE

HANDWHEEL

(QUICK DISCONNECT COUPLER)

BRASS COUPLING SLEEVE

PRESSURE

UL

RELIEF VALVE

 

NIPPLE

LIQUID LEVEL

CYLINDERINDICATOR (OPTIONAL)

REGULATOR

VENT

HOSE

Figure 3A Type I Acme Thread Quick Coupler

Figure 3B Type II Quick Disconnect Coupler

GAS SUPPLY AND MANIFOLD PRESSURES:

For Natural Gas -

For Propane Gas -

Normal 7" Water Column (w.c),

Normal 11" Water Column (w.c.)

Minimum 31/2" w.c. , Maximum 101/2" w.c.

Minimum 8" w.c., Maximum 13" w.c.

For useful advice and help with constructing your barbecue contact your local Fire Magic dealer

6

Page 6
Image 6
Fire Magic Elite 50 For Your Safety, GAS Supply and Manifold Pressures, Cylinder and Connector Requirements Specifications