Assembly
Assembly |
5 | Rim |
• While holding the ring assembly and rim together, |
turn them over. |
• Insert four screws into the holes in the rim, making |
sure each hole in the rim is still aligned with each |
screw hole in the net assembly. |
• Partially tighten the screws with a Phillips screwdriver. |
Turn the rim over to ensure that the net loops are still |
in the grooves and through the ring tabs before |
7 | Rectangular Tab |
Upper Post
4
Rim
5
6
• Hook the rectangular tab on each side of the rim to |
the upper post, as shown. |
• Rotate the rim down until it snaps into place on |
the upper post. Push down on the rim to be sure |
it is secure. |
9 | PULL HERE |
| 11 | Collar |
|
|
|
| |
|
|
|
| |
| PRESS HERE |
| Peg |
|
|
|
|
| |
| Grooves |
|
| Lever |
|
|
|
| |
|
|
| Hole |
|
|
|
|
| Opening |
| Peg | Peg | Lower | |
| Top View |
| Post |
|
| Back View |
|
| |
• Move to the side of the assembly. |
| Note: The collar may already be factory assembled. | ||
• Place your foot on the base to hold it steady. |
| |||
|
|
| ||
• Press down firmly on the lower backboard while |
| • Align the lever on the side of the collar with the | ||
rotating the backboard up. |
| opening in the top of the lower post. | ||
• When properly assembled, the pegs on the upper | • Fit the collar onto the lower post, making sure the peg | |||
post rest in the grooves in the backboard, as shown. | on each side of the collar snaps into the hole on each | |||
|
|
| side of the post. | |
Note: The height of the rim is three feet as assembled.
completely tightening the screws. Do not |
the screws. |
12
Peg
6 CurvedEnd
4
Upper Post
5
6
Large Square Opening
8
Wall
Rim
Peg
Backboard
Logo
4
Groove
5
Upper Post
Peg
Holes
Base
6
10
Lower Post
4
Rib
5
Base | 6 |
Groove
•If the lever comes off, simply re-attach it.
•Insert the peg on one side of the lever into the hole in the collar.
•Snap the other peg in the lever into the other hole in the collar.
Assembly is now complete.
•Position the base as shown.
•Position the upper post so that the straight end is down and the curved end is up and facing away from the base.
Hint: For easier assembly, apply liquid soap or rub a candle or bar soap around the bottom of the upper post (especially on the corners) and the inside of the large square opening. If assembling inside, place a tarp under the base to protect the floor surface.
• Insert the upper post into the large square opening in the base and, using a circular motion, push it all the
•Lean the rim against a wall for support.
•Locate the pegs on each side of the rim and the grooves on the backboard.
•Position the backboard with the
•Place your foot on the base to hold it steady and slide the backboard onto the upper post at an angle, as far as it will go.
Note: There should be no gap between the upper post and the backboard.
• Move the assembly away from the wall.
IMPORTANT! Assembly of the lower post is a permanent assembly.
•Align the rib on the bottom of the lower post with the groove in the opening in the base.
Hint: For easier assembly, apply a small amount of liquid soap around the bottom of the post. If assem- bling inside, place a tarp under the base to protect the floor surface.
•Insert the lower post into the opening and push down, using a circular motion, until it snaps into place.
Please refer to assembly step 2 to fill the base with water or approximately 50 lbs. of sand (water and sand not included) to keep this product stationary.
way down.
4
5
