Fluke 9140 S

Un= F New units selected

7.3 Scan

The scan rate can be set and enabled so that when the set-pointis changed the

dry-well heats or cools at a specified rate (degrees per minute) until it reaches

the new set-point. Withthe scan disabled the dry-well heats or cools at the

maximum possible rate.

7.3.1 Scan Control

The scan is controlled with the scan on/offfunction that appears in the main

menu after the temperature scale units.

Sc=OFF Scan function off

Press “UP” or “DOWN” to toggle the scan on or off.

Sc=On Scan function on

Press “SET” to accept the present setting and continue.

SAccept scan setting

7.3.2 Scan Rate

The next function in the main menu is the scan rate. The scan rate can be set

from .1 to 99.9°C/min. The maximum scan rate howeveris actually limited by

the natural heating or cooling rate of the instrument. This is often less than

100°C/min, especially when cooling.

The scan rate function appears in the main menu after the scan controlfunction.

The scan rate units are in degrees per minute,degrees C or F depending on the

selected units.

Sr= 10.0 Scan rate in°C/min

Press“UP”or“DOWN”tochangethescanrate.

Sr= 2.0 New scan rate

Press “SET” to accept the new scan rate and continue.

SAccept scan rate

9140 Dry-well Calibrator

User’s Guide

24

Contents

Main Page Table of Contents 8 Digital Communication Interface . . . . . . . . . . . . . . . . 33 9 Test Probe Calibration . . . . . . . . . . . . . . . . . . . . . . 39 Page Figures Page 1 Before You Start 1.1 Symbols Used Table1 lists the symbols used on the instrument or in this manual and the meaning of each symbol. 1.2 Safety Information 1.2.1 WARNINGS Page 1.2.2 CAUTIONS 1.3 Authorized Service Centers Page 2 Introduction 3 Specifications and Environmental Conditions 3.1 Specifications 3.2 Environmental Conditions 9 3 Specifications and Environmental Conditions Specifications 3.3 Warranty 4 Quick Start 4.1 Unpacking 4.2 Set-Up 4.3 Power 4.4 Setting the Temperature 5 Parts and Controls 5.1 Rear Panel 5.2 Front Panel 5.3 Constant Temperature Block Assembly 5.3.1 Constant Temperature Block 5.3.2 Probe Sleeves and Tongs Page 6 General Operation 6.1 Calibrator Set-Up 6.2 Changing Display Units Un= C 6.3 Switching to 230 V Operation 6.4 Setting the Temperature 6.5 Calibrating Probes Page 7 Controller Operation 7.1 Well Temperature 100.0 C 7.2 Temperature Set-point 7.2.1 Programmable Set-points Page S 7.3 Scan S 7.4 Temperature Display Hold 7.4.1 Hold Temperature Display 143.5 C U c 144.8 7.4.2 Mode Setting 7.4.3 Switch Wiring 7.4.4 Switch Test Example 7.5 Secondary Menu 7.5.1 Heater Power 100.0 C S+EAccess heater power in secondary menu SEC 12.0P 7.5.2 Proportional Band S+EAccess heater power in secondary menu SEC S 12.0P S 7.6 Controller Configuration 7.6.1 Calibration Parameters CAL 7.7 Operating Parameters PAr 7.8 Serial Interface Parameters SErIAL bAUd Page Page 8 Digital Communication Interface 8.1 Serial Communications 8.1.1 Wiring 8.1.2 Setup 8.1.3 Serial Operation 8.2 Interface Commands Users Guide Tabl e 2 9140 controller communications commands 36 37 8 Digital Communication Interface Interface Commands Tabl e 3 9140 controller communications commands continued 9 Test Probe Calibration 9.1 Comparison Methods 9.1.1 Calibrating a Single Probe 9.1.2 Comparison Calibration 9.1.3 Calibration of Multiple Probes 9.2 Dry-well Characteristics 9.2.1 Vertical Gradient 9.2.2 Heating and Cooling Rates WARNING:DO NOT remove inserts when heating or when the unit is hot. 9.2.3 Stabilization and Accuracy Figure 8 Typical Cooling Rate 41 9 Test Probe Calibration Dry-well Characteristics BlockTemperature C Page 10 Calibration Procedure 10.1 Calibration Points 10.2 Calibration Procedure 10.2.1 Compute DELTA: 10.2.2 Compute R0& ALPHA: 10.2.3 Accuracy & Repeatability 11 Maintenance 12 Troubleshooting 12.1 Troubleshooting Problems, Possible Causes, and Solutions 12.2 CE Comments 12.2.1 EMC Directive 50 12.2.2 Low Voltage Directive (Safety) Users Guide