DURBO
S4
S3
S2
S1
S1. Start/stop button
S2. Lap/reset button
S3. Mode button
S4. Light button
SPECIAL FEATURES
The Durbo features an Allen (hex) Key made of high quality stainless steel. Simply slide the Allen (hex) Key out of the watch case using your nail or a coin and make sure to snap it back in securely when done.
This Freestyle product features unique Hydro Pushers®: these pushers can be pressed under water to a dynamic water pressure (not water depth) of 3 ATM.
DISPLAY MODES
The watch has four display modes: HOME TIME (TIME) / FOREIGN TIME
HOME TIME ALARM (ALM1) / FOREIGN TIME ALARM (ALM2), STOPWATCH (STW) and TIMER (TMR).
To change from one display mode to another, press S3 button once. The mode description will appear for around 2 seconds before the selected mode is activated.
TO SET THE TIME AND CALENDAR
1.Press S2 button to select HOME TIME or FOREIGN TIME mode to set.
2.Press and hold S2 button for around 2 seconds, the message “SET” will be displayed and the second digits will blink.
3.Press S1 button to reset second digits to 00.
4.Press S3 button, the minute digits will blink
5.Press S1 button to set the minute digits.
Holding down the button will speed up the process.
6.Press S3 button, the hour digits will blink.
7.Press S1 button to set the hour digits.
8.Follow the same pattern to set the date, month, day (of the week), hour format and calendar format.
9.To set the hour format, press S1 button to toggle between
10.To set the calendar format, press S1 button to toggle between
11.After finish making all the settings, press S2 button to confirm.
NOTE: The chosen hour format and calen- dar format will apply to both HOME TIME mode and FOREIGN TIME mode.
NOTE: In FOREIGN TIME settings, only minutes, hours, date, month and day (of the week) are open to setting.
TO SET THE ALARM TIME
1.Press S3 button to select HOME TIME ALARM or FOREIGN TIME ALARM to set.
2.Press and hold S2 button for around 2 seconds, the message “SET” will be displayed and the minute digits will blink.
3.Press S1 button to set the minute digits.
Holding down the button will speed up the process.
4.Press S3 button, the hour digits will blink.
5.Press S1 button to set the hour digits.
6.After finishing making all the settings, press S2 button to confirm the settings.
TO TURN ON/OFF THE ALARM AND HOURLY CHIME
1.Press S3 button to select HOME TIME ALAM or FOREIGN TIME ALARM to set.
2.Press S1 button once to activate the daily alarm. Alarm indicator 
will appear.
3.Press again to activate the hourly chime.
Chime indicator 
will appear.
4.Press the third time to activate both functions. Both indicators will appear.
5.Press the fourth time to deactivate both functions. Both indicators will disappear.
WHEN AN ALARM OR HOURLY CHIME GOES OFF
A tune will be emitted by the hour when the hourly chime function is activated.
An alarm tune will be emitted at the designated time for around 20 seconds when the alarm is activated. To stop the tune, press any button.
TO USE THE STOPWATCH
1.Press S3 button to select STOPWATCH mode.
2.The stopwatch will then be displayed in its current state – reset, running, or stopped.
3.To resume a counting, press S1 button to resume from where it left off.
4.To start a new counting, reset the stop watch to zero first.
ENGLISH
Press S1 button to stop counting, then press S2 button to reset counter to zero.
For the measurement of elapsed time, In STOPWATCH mode,
1.Press S1 button to start counting.
2.To stop counting, press S1 button. Press S1 button again to resume from where it left off.
3.To reset to zero, press S1 button to stop counting and then press S2 button.
For the measurement of split time, In STOPWATCH mode,
1.Press S1 button to start counting.
2.While the stopwatch is running, press S2 button to register a lap. The stop- watch is still running in the back ground.
To display the currently accumulated time, press S2 button again.
3.Repeat the last step until all the laps have been registered.
4.To stop counting, press S1 button. Press S1 button again to resume from where it left off
5.To reset to zero, press S1 button to stop counting and then press S2 but- ton.
NOTE: You can leave the stopwatch running while switching over to other operating modes.
NOTE: The stopwatch will count up to 59 minutes and 59.99 seconds before start- ing from zero again.
TO SET THE TIMER
1.Press S3 button to select TIMER mode.
2.Press S2 button to alter the timer set- ting among 1, 3, 5, 10, 15, 20, 25, 30, 45 and 60 minutes.
TO USE THE TIMER
In TIMER mode,
1.Press S1 button to start counting.
2.To stop counting, press S1 button. Press S1 button again to resume from where it left off.
3.To reload the timer, press S1 button to stop counting and then press S2 button.
4.After reaching zero on a countdown, a tune will be emitted for around 20 seconds.
To stop the tune, press any button. The timer will reload automatically.
NOTE: You can leave the timer running while switching over to other operating modes.
TO USE THE BACKLIGHT
Press S4 button to turn on the backlight for around 3 seconds.
| ||
To reduce carbon foot print, these | DURBO- | |
Freestyle instructions are printed with | FS1099 | |
soy inks on recycled paper. | ||
|
