Mariner
S4
S1
S3 S2
S1. Start/stop button
S2. Mode button
S3. Set/reset button
S4. Light button
SPECIAL FEATURE:
This Freestyle product features unique Hydro Pushers®: these pushers can be pressed under water to a dynamic water pressure (not water depth) of 3 ATM.
DISPLAY MODES:
The watch has four display modes: HOME TIME (T1)/FOREIGN TIME (T2), CHORONO- GRAPH (CHRONO), TIMER and ALARM.
To change from one display mode to another, press S2 button once.
Note: In any setting mode, if there is no button pressed for a few minutes, the watch will automatically save the entered data and exit the setting procedure.
HOME AND FOREIGN TIME DISPLAY: To display FOREIGN TIME mode, press and hold S1 button when HOME TIME mode is displayed. The mode descrip- tion (T2) will be displayed and blink for approximately 5 seconds before switching to FOREIGN TIME mode. To change back to HOME TIME mode, press and hold S1 button again.
TO SET THE TIME AND CALENDAR:
1.Press S2 button to select HOME TIME (T1)/FOREIGN TIME (T2) mode.
2.Press and hold S3 button, the message “HOLD TO SET” will be displayed for approximately 3 seconds and the time zone setting will blink.
3.Press S1 button to toggle between HOME TIME (T1) and FOREIGN TIME (T2) to set.
4.Press S2 button, the hour digits will blink. Press S1 button to set the hour digits. Holding down the button will speed up the process.
5.Press S2 button, the minute digits will blink. Press S1 button to set the minute digits. Holding down the button will speed up the process.
6.Press S2 button, the second digits will blink. Press S1 button to reset the second digits to zero.
7.Follow the same pattern to set the year, month and date.
8.Press S2 button, the hour format set- ting will blink. Press S1 button to toggle between
9.Press S2 button, the hourly chime
(CHIME) setting will blink. Press S1 button to toggle between ON and OFF for the hourly chime setting.
10.When finished making all the settings, press S3 button to confirm.
NOTE: The hourly chime setting will apply to both HOME TIME mode and FOREIGN TIME mode.
TO USE THE CHRONOGRAPH:
1.Press S2 button to select CHRONO- GRAPH mode.
2.The chronograph will then be displayed in its current state – stopped, running or reset.
3.To resume a stopped counting, press S1 button to resume from where it left off.
4.To start a new counting, reset the chronograph to zero first.
Press S1 button to stop counting, then press S3 button to reset counter to zero.
For the measurement of elapsed time: In CHRONOGRAPH mode,
1.Press S1 button to start counting.
2.To stop counting, press S1 button once. Press S1 button again to resume from where it left off.
3.To reset to zero, press S1 button to stop counting and then press S3 button.
For the measurement of split time: In CHRONOGRAPH mode,
1, Press S1 button to start counting. 2, While the chronograph is running,
press S3 button once to register a lap. The split time of the registered lap will be displayed. The chronograph is still running in the background.
3.To display the current elapsed time, press S3 button again.
4.Repeat the last step until all the laps have been registered.
5.To reset to zero, press S1 button to stop counting and then press S3 button.
For the measurement of two finishes: In CHRONOGRAPH mode,
1.Press S1 button to start counting.
2.While the chronograph is running, press S3 button to register and display the time of the first runner. The chronograph is still running in the background.
3.Press S1 button to stop and register the time of the second runner.
4.Press S3 button to display the time of the second runner.
5.To reset to zero, press S3 button again.
NOTE: The chronograph can count up to a maximum of 23 hours, 59 minutes and 59.99 seconds.
NOTE: You can leave the chronograph running while switching over to other operating modes.
TO SET THE TIMER:
1.Press S2 button to select TIMER mode.
2.Press S3 button, the message “HOLD TO SET” will be displayed for approxi- mately 3 seconds and the hour digits will blink.
3.Press S1 button to alter the timer set- ting among 60, 55, 50, 45, 40, 35, 30, 25, 20, 15, 14, 13, 12, 11, 10, 9, 8, 7, 6, 5, 4, 3, 2, and 1 minutes.
4.Press S2 button, the
ENGLISH
REPEAT AT END (REPEAT) and COUNT UP AT END (UP).
5.When finished making all the settings, press S3 button to confirm.
NOTE: Definitions of
a)STOP AT END – the timer will stop when the countdown reaches zero.
b)REPEAT AT END – the timer will repeat the countdown when the countdown reaches zero.
c)COUNT UP AT END – the timer will count up to a maximum of 23 hours 59 minutes and 59 seconds when the countdown reaches zero.
TO USE THE TIMER:
1.Press S3 button to select TIMER mode.
2.The timer will then be displayed in its current state – stopped, running, or reset.
3.To resume a stopped counting, press S1 button to resume from where it left off.
4.To start a new counting, reload the timer first.
Press S1 button to stop counting, then press S3 button to reload the timer.
5.When reaching zero in a countdown, a tune will be emitted. To stop the tune, press any button.
NOTE: You can leave the timer running while switching to other operating modes.
TO SET THE ALARM TIME:
1.Press S2 button to select ALARM mode.
2.Press and hold S3 button, the message “HOLD TO SET” will be displayed and the hour digits will blink. Press S1 but- ton to set the hour digits. Holding down the button will speed up the process.
3.Press S2 button, the minute digits will blink. Press S1 button to set the minute digits. Holding down the button will speed up the process.
4.When finished making all the settings, press S3 button to confirm.
NOTE: The alarm will automatically be activated after being set.
TO TURN ON/OFF THE ALARM:
In ALARM mode, press S1 button to toggle between ON and OFF of the alarm. When the alarm is ON, the alarm indicator 
will appear.
WHEN AN ALARM GOES OFF:
A
TO USE THE BACKLIGHT:
Press S4 button to turn on the backlight for 3 seconds.
To reduce carbon foot print, these | MARINER | |
119FS | ||
Freestyle instructions are printed with | ||
soy inks on recycled paper. |
|
