Frigidaire 131956700A manual Features, Common Drying Problems, Problem Possiblecauses Solutions

Features

Place the front bar under

the lip of the lint screen opening.

Cycle Signal Control (some models)

When the Cycle Signal Control is ON, a signal will sound at the end of each cycle and during the Press Saver setting (some models). The volume is adjustable on some models.

Drum Light (some models)

A drum light will come on whenever the door is opened to illuminate the dryer drum during loading and unloading. Closing the door turns off the light.

Reversible Dryer Door

Your dryer is equipped with a reversible door. The door can be hinged on the right orleftside.RefertotheINSTALLATIONINSTRUCTIONSfordirectionsonchanging the door.

Drying Rack (some models)

Use the drying rack to dry items which should not be tumble dried.

1.Open the dryer door and remove the lint screen.

2.Insert drying rack into the dryer drum. Place the front bar under the lip of the lint screen opening.

3.Place items to be dried on top of the rack. Weight should not exceed 10 lbs. Leave space between items, but do not let items hang over the sides or through the grids. Do not tumble other items when using the drying rack.

4.Select a timed dry setting best suited for items being dried. Use only the Air Fluff (no heat) temperature setting for items containing plastic, foam rubber, rubber-like materials, feathers or down.

5.When items are dry, remove the rack and replace the lint screen. If lint screen is not in place, tumbling items could enter the exhaust system and cause damage to the dryer.

Common Drying Problems

Many drying problems involve poor cleaning results, poor soil and stain removal, residues of lint and scum, and fabric damage. For satisfactory drying results, follow these suggestions provided by The Soap and Detergent Association.

PROBLEM POSSIBLECAUSES SOLUTIONS PREVENTIVEMEASURES

Greasy, oily • Fabric softener sheet.	• Rub fabric softener stains with bar soap.
stains	Rinse and rewash.

•Add a few bath towels to small loads for proper tumbling.

•Some "silk-like" fabrics should be air dried.

•Use proper drying temperature.

•Place fabric softener sheet on top of load before starting the dryer.

Lint	•	Overloading.	• Reduce load size and rewash using liquid	• Do not overload dryer.
	•	Overdrying causes static	fabric softener in the final rinse.	• Use fabric softener in washer or dryer to
		electricity.	• Or, add a fabric softener sheet and	reduce static electricity.
	•	Lint screen not clean	tumble without heat.	• Remove items when they are slightly damp
		when cycle began.	• Use lint brush or roller to remove lint.	to avoid overdrying.
	•	Lint is attached to "pills."		• Check that lint screen is clean and in place.
Pilling	•	Pilling is normal with	• Use a lint brush or shaver to remove pills.	• Use fabric softener to lubricate fibers.
(Fibersbreak		synthetic and permanent		• When ironing, use spray starch or fabric
off, ball up and		press fabrics. This is due		finish on collars and cuffs.
cling to fabric.)		to abrasion from normal		• Turn items inside out to reduce abrasion.
		wear.
Shrinking	•	Overdrying.	• Irreversible condition.	• Follow fabric care label directions.
				• If shrinking is a concern, check load often.
				• Remove items while slightly damp and
				hang or lay flat to complete drying.
				• Block knits into shape.

Wrinkling	•	Overloading.
	•	Leaving items in dryer
		after cycle ends.

•	Reduce load size and tumble at medium	•	Do not overload dryer.
	or low heat for 5-10 minutes.	•	Remove items as soon as cycle ends.
•	Remove items immediately. Hang or fold.

5