Frigidaire 700 Series manual Electrical Connection for a PortablelConvertible Dishwasher, Sure

Connecting and Disconnecting the Portable/ Convertible Dishwasher

The portable/convertible

dishwasher must be connected to a faucet and electrical outlet each time it is used.

Follow directions

on this

page

to properly

connect

dishwasher.

Faucet

Adapter

Assembly

IMPORTANT:

Make

sure

door

is latched

before

moving

dishwasher.

in

_

The

power

cord,

faucet

coupler

and hoses

are

located

in a compartment

back of dishwasher. A special adapter must be installed on faucet before you

Per Outside

For Inside

can

connect

dishwasher.

Threaded

1.

Remove

faucet

adapter

assembly

from

literature

package.

Threaded

Faucet

2.

Unscrew

existing

sink

faucet

aerator.

Faucet

Use

3.

Check faucet

spout

to

see

if threads

are

inside

or

outside.

;'Thick

Use

and

•

If threads

are

on

inside

of faucet

spout,

use

both

thick

and thin rubber

Washer

Thin

washers.

Only

Washers

•

If threads

are

on

outside

of faucet

spout,

use thin

rubber

washer

only.

Adapter_--..(

Two Brass

•

If faucet

has

no

threads,

an adapter

kit with

instructions

for attachment

(Dual

Screens

to a non-threaded

spout

is available

at most

hardware

stores.

Thread)

should be

4.

Assemble

faucet

spout

as

shown.

Make

sure

the

two brass

screens

are

below

the

rubber

located

below

the

rubber

washers.

washers

Connecting

the

Portable/Convertible

Dishwasher

Connecting the

Portable

1.

Run

water

at

faucet

until

it is

hot. Turn

off

faucet.

Faucet

Adapter

Assembly

2.

Pull

hoses

out

of compartment.

3.Push collar down and slip faucet connector onto faucet adapter.

4.When connector snaps into place, release collar.

5.Slowly turn on hot water all the way.

6.Plug power cord into grounded outlet.

	Getting	Water	While	Dishwasher	is Running
	You can	get water from		the faucet	while	the dishwasher is connected.
Coupler	However,	avoid	getting	water when	the	dishwasher is filling or draining.

1.Press red button on coupler to get the water you want. The faucet is set on hot, adjust faucet if you want cold.

2.Be sure hot water is turned back on all the way to complete cycle.

Avoid fire hazard or electrical shock. Do not

use an adapter plug, extension cord or remove

grounding prong from electrical power cord.

Failure to follow this warning can cause serious injury, fire or death.

Disconnecting the Portable/Convertible Dishwasher

1.When cycle has finished, turn off hot water.

2.Press red button on coupler to release water pressure being careful not to release coupler.

3.Press down on collar to release coupler.

4.Empty remaining water from coupler and return it to compartment.

5.Unplug power cord and return it to compartment.

IMPORTANT: A sink spray attachment hose can burst due to constant water pressure while in use. If your spray hose is installed on same water line as the dishwasher, we suggest you disconnect the sink spray attachment and plug the hole.

Power supply cord with 3-prong grounding plug

Electrical Connection for a PortablelConvertible Dishwasher

An electrical supply of 120 volts, 60 Hz, AC only, 15 amps is required. For your safety, the dishwasher must be grounded. If there is a malfunction or breakdown, grounding will reduce risk of electrical shock. This dishwasher has a power cord with a 3-prong grounding plug. It must be plugged into a mating

3-prong grounding type receptacle, installed and grounded in accordance with the National Electrical Code and any local codes and ordinances.

Grounding type wall receptacle

Do not under any circumstances cut, remove or bypass the grounding prong from this plug.

Converting to Built-In

Your portable dishwasher can be converted to a built-in (undercounter) model. A conversion kit No. 154241302 is required and is available from your local dealer or distributor. Instructions are included with the kit.

12