MAX3147RC, MAX3073RC, MAX3036RC

HARD DISK DRIVES INSTALLATION GUIDE

CARE OF YOUR FUJITSU DRIVE

Careful handling and installation of your disk drive is paramount to the longevity of the unit. The internal mechanism of the drive can be seriously damaged if the casing is subjected to forces outside the environmental specifications. When transporting the drive, always use the original packing in which the drive was delivered to you, and avoid exposing the drive to extreme changes in temperature to minimize the risk of condensation.

Handling

1.Never drop the unit. Handle it with care.

2.Never move the disk drive while disks are spinning. Note that the disks spin when the drive is powered on and also immediately after power off. Refer to the Start/Stop specification for your drive.

3.Never place the drive in the vicinity of equipment giving off strong magnetic fields, such as monitors, televisions, or loudspeakers.

4.Never use any cleaning agents or liquids on the drive.

5.Always use an antistatic mat and wrist strap when handling the drive. Hold the drive by the base casting and never touch the components on the printed circuit board.

6.Never remove any labels from the drive or deface them in any way.

7.Never open the disk enclosure for any reason. Doing so will void any warranties.

8.Always pay close attention to the mounting specifications such as those for sway space and cooling. If the temperature difference between the storage location and installation location exceeds 10°C, for temperature acclimation purposes, leave the drive in the new location for at least two hours before turning it on. This minimizes any risk of condensation forming on the drive.

The Drive needs NO preventative or periodic maintenance during its service life if properly used in an appropriate environment.

INSTALLATION

1.ORIENTATION

The drive can be installed flat on any of its six sides. Inclination from a vertical or horizontal plane should not exceed 5°.

2.MOUNTING SCREW INSTALLATION

When the mounting screw holes on the side of the drive are used, be sure to use the two pairs of outer holes. Do not use the center hole in conjunction with only one of the outer holes. The screws must not penetrate the drive by more than 5.0 millimeters. Impact caused by the electric driver must be within the device specifications.

3.COOLING

Allow space above and below the drive to provide an adequate air flow. Fan cooling is recommended. The disk enclosure temperature measured at center of base cover (label side) should never exceed 60 °C. See Table 1.

Table 1. Reference value of airflow

Environmental temperature

Required velocity of airflow

30°C

> 0.3 m/s

35°C

> 0.6 m/s

40°C

> 0.9 m/s

45°C

> 1.5 m/s

4.BREATHING

Never cover the vent hole displayed on the label with the arrow.

5.CONNECTING

To avoid potential damage to the drive, make sure that connector type and orientation is correct.

CAUTION: Your warranty may be voided if the connector is damaged as a result of incorrect insertion.

FUJITSU LIMITED

Storage Products Group

4-1-1 Kamikodanaka, Nakahara-ku, Kawasaki 211-8588, Kanagawa-ken, Japan

Copyright © 2005 FUJITSU LIMITED

http://www.fujitsu.com/

C141-E238-01EN

Page 1 Page 1
Page 1
Image 1
Fujitsu C141-E238-01EN specifications MAX3147RC, MAX3073RC, MAX3036RC, Hard Disk Drives Installation Guide
Page 1 Page 1

C141-E238-01EN specifications

The Fujitsu C141-E238-01EN is a state-of-the-art multifunctional printer that caters to the diverse needs of modern office environments. Renowned for its reliability and efficiency, this device embodies Fujitsu's commitment to quality and innovation.

One of the prominent features of the C141-E238-01EN is its high-speed printing capability. It can produce up to 30 pages per minute, making it an ideal choice for businesses that demand quick turnaround times. This printer supports a variety of media sizes, including A4, A5, and even custom sizes, which adds versatility to its functionality.

The C141-E238-01EN incorporates advanced printing technologies to ensure exceptional print quality. With a maximum resolution of 1200 x 1200 dpi, it delivers sharp text and vibrant graphics, making it suitable for producing professional documents and marketing materials. The printer also supports automatic duplex printing, which not only saves paper but also reduces the environmental impact of printing.

Connectivity is another strong point of the C141-E238-01EN. It offers USB, Ethernet, and wireless connectivity options, allowing users to print seamlessly from various devices, including computers, tablets, and smartphones. The compatibility with mobile printing solutions enhances its usability, enabling users to print on-the-go from their preferred mobile applications.

In terms of usability, the C141-E238-01EN features an intuitive control panel with a user-friendly interface. This makes navigation easy and allows users to access essential functions quickly. The large paper capacity of up to 250 sheets reduces the frequency of paper refills, enhancing productivity in busy office settings.

Fujitsu has prioritized energy efficiency in the design of the C141-E238-01EN. It complies with Energy Star standards, ensuring minimal power consumption without compromising performance. This not only helps reduce operational costs but also contributes to corporate sustainability initiatives.

In conclusion, the Fujitsu C141-E238-01EN stands out as a reliable and efficient multifunctional printer, equipped with advanced printing technologies and user-friendly features. Its high-speed printing, superior print quality, versatile connectivity options, and energy-efficient design make it an invaluable asset for any professional environment.
Top Page Image Contents