Manuals / Fujitsu / Computer Equipment / Scanner

Fujitsu M3096GX, M3096EX manual Table B.1 LED at an error

Models: M3096GX M3096EX

1 53

Download 53 pages 15 Kb

Page 49

(2)Activating the continuous operation test

Open the ADF and close it again. If no document is loaded on the ADF within five seconds after closing the ADF cover, the image scanner runs in flatbed mode. If docu- ments are loaded on the ADF within five seconds after closing the ADF cover, the image scanner continuously feeds the document from ADF. Once the image scanner start reading documents in the flatbed mode, it does not feed documents from ADF even if documents are loaded on the ADF.

(3)Ending the test in flatbed mode

To stop the carrier movement in flatbed mode, open the ADF cover. If the ADF cover is opened, the POWER lamp starts blinking immediately after the carrier returns to the home position.

(4)Ending the test in ADF mode

If the ADF document hopper is empty, feeding documents from the ADF ends. To restart feeding, open the ADF cover and close it again. Then load documents on the ADF docu- ment hopper within five seconds after closing the ADF cover.

(5)LED status on error

If an error occurs during the test, the LED indicates as shown in table B.1.

If paper is jammed in the ADF, remove the jam and close the ADF. The CHECK lamp stops blinking about three seconds after closing the ADF cover. To feed the document from ADF, open and close the ADF.

Table B.1 LED at an error

Errors/Alarm	POWER lamp	READ lamp	CHECK lamp

Paper jam	On	Off	Blink

Carrier drive alarm	Blink	Off	On

Optical system alarm	Blink	Off	Blink

Motor fuse failure	Blink	On	On

Lamp fuse failure	Blink	On	Blink

B – 2

Image 49

Fujitsu M3096GX, M3096EX manual Table B.1 LED at an error

Contents

C150-E009-07EN M3096EX AND M3096GX IMAGE SCANNER OPERATOR’S GUIDEREVISION RECORD Revised contentsEdition Date publishedConventions CHAPTER 3 INSTALLATION AND CONNECTIONS CONTENTSpage 4.2.3 Reading a document larger than the document boardTROUBLESHOOTING MAINTENANCEFIGURES SCSI-ID setting TABLESInstallation specifications LED at an errorTable 1.1 The differences between the M3096EX and the M3096GX CHAPTER 1 PREFACEThis page is intentionally left blank 2.1 Checking the Components CHAPTER 2 COMPONENTS2.2.1 Exterior view of image scanner 2.2 Part Names and FunctionsFigure 2.2 M3096EX/GX parts names Presses a document to the document bed 2.2.2 Functions of each partOpens or closes the automatic document 2.4 Operator Panel Functions LCD model 2.3 Indication Panel Functions standard modelFigure 2.3 M3096EX/GX Indication panel 2.3.1 Indicators Figure 2.4 M3096EX LCD model operator panel2.4.2 Buttons and liquid crystal display screen 2.4.1 Indicators2.4.3 Liquid crystal display screen A D F ASize button Automatic document feeder ADF buttonDensity button Resolution buttonHalftone button Landscape buttonUpper line Lower lineDocument button Mode 1 and 2 button2.4.4 Messages Error messages temporary errors N o w R e a d i n g W a r m i n g - u p N o wA D F L G 4 0 0 H T 2 L . R e a d y3.1 Precautions CHAPTER 3 INSTALLATION AND CONNECTIONS3.2 Removing the Carrier Fixing Bracket 3.3 Connections M3096GX Mount the stacker and extensions using the following procedure 3.4 Mounting the StackerHook the pins on the stacker to the claws on the image scanner ① Mount the stackerFigure 3.1 SCSI-ID setting Table 3.1 SCSI-ID setting 3.5 SCSI-ID SettingAddress switch CHAPTER 4 OPERATIONS 4.1 Turning on the Power4.2.1 Reading a standard-size document 4.2 Reading a Document in Flatbed ModePortrait mode Landscape modeFigure 4.1 Flatbed reading 4.2.2 Reading a page from a thick bookFigure 4.2 Removing the document cover 4.2.3 Reading a document larger than the document board4.3 Reading Documents in ADF Mode Section A enlargerd ③ Pull up the ADF paper chute as follows A4 or letter size or smaller 4 mm or less Figure 4.4 Loading the document This page is intentionally left blank 5.1 Removing Jammed Documents CHAPTER 5 MAINTENANCE① ② ③ ④ 5.2 Notes on Daily Use 5.3 CleaningFigure 5.3 Cleaning the ADF 5.3.2 Cleaning the ADFEjection roller Clean the roller on the opposite side also Pick spring5.4.1 Parts number and replacement cycle 5.4 Consumables/Periodical replacement parts5.4.2 Replacing pad ASY 5.4.3 Replacing pick roller Figure 5.4 Pick Roller replacementFigure 5.6 Slide the Pick Roller Figure 5.5 Move the Retaining springFigure 5.7 Remove the Pick Roller CHAPTER TROUBLESHOOTINGTable 6.1 Check items Paper double feed Table 6.1 Check items continuedAPPENDIX A A.1 Installation SpecificationsFigure A.1 External dimensions A.2 External Dimensions497 173 696 Unit mm APPENDIX B B.1 Test mode for maintenanceTable B.1 LED at an error APPENDIX C C.2 IPC-2/CMP-2 option board installationC.1 Option IPC-2 option board Screw for IPC-2 Flat cable Flat cable connectorCMP-2 option board or memory PCA M3096GX not shown Screw for memory or CMP-2 M3096GXFUJITSU NORDIC AB FUJITSU LIMITEDInternational Operations Kung Hans vag, S-191 76 Sollentuna, SWEDENReader Comment Form What is your overall rating of this publication?