CATALYST™ 48
UNIVERSAL REMOTE CONTROL
USER GUIDE
INTRODUCTION
The Catalyst™ 48 Universal Remote Control, developed by Universal Electronics, Inc. for Funai, is the complete solution for all of your remote control requirements. It is designed to operate from four to eight devices with the emphasis on features and functions of your dedicated component(s).
The Catalyst 48 requires two (2) fresh
AAalkaline batteries (not included) and some easy programming to control your devices. For best results, please read and perform all instructions listed here. Also, keep these instructions for future reference.
FEATURES AND FUNCTIONS
Use the Key Charts to learn how the Catalyst 48 functions.
Key Charts
The LED (red light) blinks to show that the remote control is working and is sending signals.
Use SETUP for all programming sequences.
Press PWR once to turn on or off the selected home enter- tainment component.
Press AUX, CBL, VCR, TV, SAT, CD, AMP, or TNR once to select a home entertainment component to control.
Use the keypad (0 ~ 9) to directly select channels (for example, 09 or 31).
Press MUTE once to turn sound off
or on.
Press ENTER once after entering channel numbers on some TV models.
Use VOL + (or VOL
Use CH + (or CH
Press LAST once to recall the last channel and to page back one screen in the
main menu.
Press SLEEP to activate your TV’s sleep timer. Or if none is available, press SLEEP to activate the Catalyst 48’s sleep timer for automatic
Press INPUT once to switch the input of the chosen component.
Use GUIDE to display the program guide.
Use EXIT to exit out of the selected compo- nent’s menu or guide.
Use the cursor keys to move the cursor in the program guide and menu screens.
Use SELECT to choose options from your selected component’s menu or guide.
Use INFO to display current channel and program information.
Press MENU to access the menu of your chosen component.
Use the transport keys to control your VCR, or CD or DVD player.
Use these keys for specific features on your dedicated components.
INSTALLING BATTERIES
1.On the back of the Catalyst 48, push the tab and lift off the battery cover.
2.Obtain two (2)
– marks in the battery case, then insert the new batteries.
3.Press the battery cover back into place. The tab should click when the cover is locked.
4.Test the unit by pressing PWR and any mode key (e.g., AUX, CBL, VCR, etc.). If the batteries are inserted cor- rectly, the LED will blink once.
NOTE: When batteries need replacement, the Catalyst 48 will blink twice with every key press. Simply replace them and the remote control will be restored to its full functionality, including favorite settings.
PROGRAMMING
COMPONENT CONTROL
The Catalyst 48 can control up to eight different components. Perform the fol- lowing instructions for each component you want controlled:
NOTE: For TV/VCR Combo control, see the next section.
1.Turn on a component (e.g.,VCR) and, if applicable, insert media, (e.g., cassette or disc).
NOTE: Please read steps
2.On the Catalyst 48, press a component key once (i.e., AUX, CBL, VCR, TV, SAT, CD, AMP, or TNR). Press and hold SETUP until the LED blinks twice, then release SETUP.
3.Use the Manufacturer’s Codes (on the back side) to locate the the type of component and brand name and then enter the first
NOTE: If the LED did not blink twice, then repeat steps 2 through 3 and try entering the same code again.
4.Aim the Catalyst 48 at the component and press PWR once. It should turn off. If it does not respond, repeat steps
NOTE: If the device does not have a PWR key, press PLAY.
5.Repeat steps 1 through 4 for each component you want the Catalyst 48 to control.
PROGRAMMING
TV/VCR COMBO CONTROL
Perform the following instructions to control a TV/VCR Combo:
1.Turn on the TV/VCR Combo and insert a video cassette.
NOTE: Please read steps
2.On the Catalyst 48, press VCR. Press and hold SETUP until the LED blinks twice, then release SETUP.
3.Use the Setup Codes For TV/VCR Combos (on the back side) to locate the brand name and then enter the first
NOTE: If the LED did not blink twice, then repeat steps 2 through 3 and try entering the same code again.
4.Aim the Catalyst 48 at the component and press PWR once. It should turn off. If it does not respond, repeat steps
NOTE: If the device does not have a PWR key, press PLAY.
5.If you’ve located a setup code that works, but it has a separate TV code, you’ll also need to program it into the Catalyst 48 to access volume control as follows:
a.Press TV once. The LED will blink twice.
b.Enter the TV code for your TV/VCR Combo. If correct, the LED will blink twice.
If there is no separate TV code listed, you will need to perform the follow- ing steps to access volume control:
a.Press and hold SETUP until the LED blinks twice, then release
SETUP.
b.Enter 9 - 9 - 3 . The LED will blink twice.
c.Press VCR once. The LED will blink twice.
SEARCHING FOR YOUR CODE
If your device does not respond to the Catalyst 48 after trying all codes listed for your brand, or if your brand is not listed at all, try searching for your code. For example, to search for a code for your TV:
1.On the Catalyst 48, press TV once.
2.Press and hold SETUP until the LED blinks twice, then release SETUP.
3.Enter 9 - 9 - 1. The LED will blink twice.
4.Aim the remote control at the the TV and slowly alternate between pressing PWR and TV. Stop when the TV turns off.
NOTE: In the search mode, the Catalyst 48 will send IR codes from its library to the selected device, starting with the most popular code first.
5.Press SETUP once to lock in the code.
6.To search for the codes of your other components, repeat steps 1 through 5, but substitute the appropriate key (i.e., AUX, CBL, VCR, SAT, CD, AMP, or
TNR) for the (Auxiliary,VCR, Cable, Satellite, CD, Amplifier, or Tuner) component you are searching for.
CHECKING THE CODES
If you have set up the Catalyst 48 using the Searching For Your Code procedure, you may need to find out which four- digit code is operating your equipment:
For example, to find out which code is operating your TV:
1.On the Catalyst 48, press TV once.
2.Press and hold SETUP until the LED blinks twice, then release SETUP.
3.Enter 9 - 9 - 0. The LED will blink twice.
4.To view the code for the first digit, press 1 once. Wait 3 seconds, count the LED blinks (e.g., 3 blinks = 3) and write down the number.
NOTE: If a code digit is “0”, the LED will not blink.5.Repeat step 4 three more times for remaining digits. Use 2 for the sec- ond digit, 3 for the third digit, and 4 for the fourth digit.
6.To check for the codes of your other components, repeat steps 1 through 5, but substitute the appropriate key (i.e., AUX, CBL, VCR, SAT, CD, AMP, or
TNR) component you are checking. As before, write down each four- digit code.
The Catalyst 48 can be set up to control a second TV or VCR, or any combination of eight home entertainment components.
For example, to have the Catalyst 48 con- trol a TV, a Cable Converter, and two VCRs, you will need to
1.On the Catalyst 48, press and hold SETUP until the LED blinks twice, then release SETUP.
2.Enter 9 - 9 - 2. The LED will blink twice.
3.Press VCR once, then press AUX once.
4.The AUX key is now ready to be pro- grammed for your second VCR. See Programming Component Control.
To
To |
|
Sequence | Perform |
TV as 2nd VCR key: | SETUP - 9 - 9 |
| - 2 - VCR - TV |
TV as 2nd CBL key: | SETUP - 9 - 9 |
| - 2 - CBL - TV |
TV as 2nd AUX key: | SETUP - 9 - 9 |
| - 2 - AUX - TV |
TV as 2nd TNR key: | SETUP - 9 - 9 |
| - 2 - TNR - TV |
TV as 2nd AMP key: | SETUP - 9 - 9 |
| - 2 - AMP - TV |
TV as 2nd CD key: | SETUP - 9 - 9 |
| - 2 - CD - TV |
TV as 2nd SAT key: | SETUP - 9 - 9 |
| - 2 - SAT - TV |
TV back to TV: | SETUP - 9 - 9 |
| - 2 - TV - TV |
VCR as 2nd TV key: | SETUP - 9 - 9 |
| - 2 - TV - VCR |
VCR as 2nd CBL key: | SETUP - 9 - 9 |
| - 2 - CBL - VCR |
VCR as 2nd AUX key: | SETUP - 9 - 9 |
| - 2 - AUX - VCR |
VCR as 2nd TNR key: | SETUP - 9 - 9 |
| - 2 - TNR - VCR |
VCR as 2nd AMP key: | SETUP - 9 - 9 |
| - 2 - AMP - VCR |
VCR as 2nd CD key: | SETUP - 9 - 9 |
| - 2 - CD - VCR |
VCR as 2nd SAT key: | SETUP - 9 - 9 |
| - 2 - SAT - VCR |
VCR back to VCR: | SETUP - 9 - 9 |
| - 2 - VCR - VCR |
AUX as 2nd TV key: | SETUP - 9 - 9 |
| - 2 - TV- AUX |
AUX as 2nd VCR key: | SETUP - 9 - 9 |
| - 2 - VCR - AUX |
AUX as 2nd CBL key: | SETUP - 9 - 9 |
| - 2 - CBL - AUX |
AUX as 2nd TNR key: | SETUP - 9 - 9 |
| - 2 - TNR - AUX |
AUX as 2nd AMP key: | SETUP - 9 - 9 |
| - 2 - AMP - AUX |
AUX as 2nd CD key: | SETUP - 9 - 9 |
| - 2 - CD - AUX |
AUX as 2nd SAT key: | SETUP - 9 - 9 |
| - 2 - SAT - AUX |
AUX back to AUX: | SETUP - 9 - 9 |
| - 2 - AUX - AUX |
When a
CHANGING VOLUME LOCK
The Catalyst 48 is set to control volume of a component through your TV while in the TV,VCR, Cable, or Satellite mode. However, in an Audio mode (i.e., TNR, AMP, or CD), you have separate control of your audio component’s volume.
If your TV is not remote controllable, or if you want volume to be controlled by a different component, you can change the Volume Lock setting to control a volume through a
To change Volume Lock to the another mode:
1.On the Catalyst 48, press and hold SETUP until the LED blinks twice, then release SETUP.
2.Enter 9 - 9 - 3 and then press any mode key once (except TV). The LED will blink twice.
3.Now, whenever you press VOL +, VOL
To change Volume Lock back to the TV mode:
1.On the Catalyst 48, press and hold SETUP until the LED blinks twice, then release SETUP.
2.Enter 9 - 9 - 3 and then press TV. The LED will blink twice.
3.Now, whenever you press VOL +, VOL
TROUBLESHOOTING
PROBLEM: LED does not blink when you press a key.
SOLUTION: Replace the batteries with two (2) new AA alkaline batteries.
PROBLEM: LED blinks when you press a key, but home entertainment component does not respond.
SOLUTION: Make sure the Catalyst 48 is aimed at your home entertainment component and is not farther than 15 feet away.
PROBLEM: Catalyst 48 does not con- trol home entertainment components or commands are not working properly.
SOLUTION: Try all listed codes for the component brands being set up. Make sure they can be operated with an infrared remote control.
PROBLEM: TV/VCR combo does not respond properly.
SOLUTION: Use the VCR codes for your brand. Some combo units may require both a TV code and a VCR code for full operation.
PROBLEM: No volume on a 2nd TV.
SOLUTION: Follow instructions in Changing Volume Lock.
PROBLEM: CH+ ,
SOLUTION: Due to RCA design (1983- 1987), only the original remote control will oper- ate these functions.
PROBLEM: Changing channels does not work properly.
SOLUTION: If original remote control required pressing ENTER to change channels, press ENTER on the Catalyst 48 after entering the channel number.
PROBLEM: Tried “Search Method” and still could not find a working code.
SOLUTION: Try the “Search Method” again after clearing out the device key as follows: Press and hold SETUP until the red light blinks twice, then release. Next enter 9 - 9 - 2. Then press and release the device key to be cleared twice.
Continued on back...