PREPARATION FOR USE
CONNECTIONS
Plug the incoming cable into the ANT. IN jack on the rear of the TV.
INSTALLING THE BATTERIES |
| |||
1 | 2 | 3 | Install two AA batteries (supplied) | |
matching the polarity indicated inside | ||||
|
|
| ||
|
|
| battery compartment of the remote con- | |
|
|
| trol. | |
Cable OR Antenna
TV signal
Incoming cable from home Antenna /
Cable Company (No Cable Box)
Rear of this TV
[BATTERY PRECAUTIONS]
• Be sure to follow the correct polarity as indicated in the battery compartment. |
Reversed batteries may cause damage to the device. |
• Do not mix different types of batteries together (e.g. Alkaline and |
with fresh ones. |
• If the device is not to be used for a long period of time, remove the batteries to prevent |
OR
Cable Box or Satellite Box*
OUT
IN 
ANT. IN
damage or injury from possible battery leakage. |
• Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. |
OPERATIONS
Incoming cable from Cable Company or Satellite Antenna
REMOTE CONTROL AND FRONT PANEL FUNCTION
*Note (DO NOT DISCONNECT FROM BOX)
Some cable TV systems use scrambled signals and
*Cables not includedrequire a special converter to receive these channels. Consult your local cable company.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
Note:
•For your safety and to avoid damages to the unit, unplug the antenna cable from the ANT. IN jack before moving the unit.
IR transmitter
To send infrared ray (IR) signal
POWER button
To turn TV on/off
Channel number buttons
Press two digits to directly access the desired channel. Remember to press a "0" before a single digit channel.
CH(ANNEL) K / L buttons
To select channels and move up/down through menu items
POWER |
| GAME SLEEP | |
|
|
| DISPLAY |
1 | 2 | 3 |
|
4 | 5 | 6 | CHANNEL |
|
|
| |
|
|
| RETURN |
7 | 8 | 9 |
|
| 0 | +100 | INPUT |
|
|
| |
|
|
| SELECT |
|
| CH |
|
| VOL |
| VOL |
|
| CH |
|
|
|
| MUTE |
MENU |
|
|
|
GAME button
Press to set the Game mode
SLEEP button
To set Sleep Timer
DISPLAY button
To display CH No./Audio Status
CHANNEL RETURN button
To return previous screen
INPUT SELECT button
To select TV or external input
MUTE button
[EXTERNAL CONNECTION]
VIDEO1 INPUT (Rear)
ex. |
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
(OUT)
(OUT)
(IN)
(IN)
Rear of this TV
L | ANT.IN |
|
AUDIO IN
R
MENU button To view
To mute sound
VOL(UME) K / L buttons To adjust volume
To decide the command of settings
Video Cassette Recorder
Audio Cable
Note:
●You can test if the remote control sends out the infrared signal with an AM radio. (Refer to “TROUBLESHOOTING GUIDE”.)
Note:
●The AUDIO L jack is for mono input. The sound is heard from both speakers. Use this jack for connecting monaural audio equipment.
VIDEO2 INPUT (Front)
ex. | Audio Cable |
| |
| (OUT) |
| Video Cable |
Video Camera | (OUT) |
Video Game |
| (IN) |
VIDEO | L - AUDIO - R |
(IN) |
|
Front of this TV
VIDEO | L - AUDIO - R | HEADPHONE | MENU | VOLUME | CHANNEL | POWER |
Infrared Sensor Window
POWER button
Note:
●The AUDIO L jack is for mono input. The sound is heard from both speakers. Use this jack for connecting monaural audio equipment.
SELECTING AUDIO/VIDEO INPUT
When you use the AUDIO/VIDEO input jacks, select “VIDEO1” or “VIDEO2” mode by pressing [INPUT SELECT] on the remote control. The input mode changes by pressing the button as following:
INPUT | TV channel | VIDEO1 (Rear) | VIDEO2 (Front) |
SELECT |
|
|
|
|
|
|
|
•To use the jacks on the rear of the TV, select “VIDEO1”.
•To use the jacks on the front of the TV, select “VIDEO2”.
CHANNEL ▲ /▼ buttons
VOLUME X/Y buttons
MENU button
HEADPHONE jack
AUDIO L/R input jacks
VIDEO input jack
Note:
●If some digits appear in the corner of the screen when the unit is turned on at the first time, press [POWER] without unplugging the power cord.
SLEEP TIMER SETTING
1
SLEEP
2
SLEEP
SLEEP 0
repeatedly
SLEEP 10
Notes:
●When you disconnect the unit from the AC outlet or when you have a power failure, the sleep time will be lost.
●To cancel the sleep timer, press [SLEEP] repeatedly until “SLEEP 0” is displayed.
●The Sleep Timer Setting display will disap- pear automatically after 10 seconds of the operation.
The time increases by 10 minutes up to 90.
