Manuals / Brands / Marine Equipment / Fish Finder / Furuno / Marine Equipment / Fish Finder

Furuno FR-8122, FR-8252, Fr8062 2.3 Port for External Devices

1 56

Download 56 pages, 6.63 Mb

2. WIRING

2-4

2.3 Port for External Devices

External equipments can be connected here as shown below.

NMEA1(7P) NMEA2(7P) HDG (6P) PC/EXT-BUZZER

(7P)

NMEA sentence

device

NMEA sentence

device

Heading sensor External buzzer,

PC, etc.

This equipment can receive the following NMEA 0183 format sentences from other

equipment. You will need the optional NMEA cable to connect with external equipment.

• Course: VTG> RMC

• Waypoint Range: BWR> BWC> RMB, Bearing: BWR> BWC (> RMB*1)

• Heading (True): HDT> VHW> HDG*2> HDM*2> VHW*2

• Heading (Magnetic): HDG> HDM> VHW> HDT*2> VHW*2

• Ship’s speed: Over ground: VTG>RMC> VHW, Through water: VHW

• Date: ZDA

• Time: ZDA

• Own ship’s position: GNS>GGA>RMC> GLL

• Depth: DPT>DBT

• Wind speed and angle*3: True: MWV>VWT, Relative: MWV>VWR

• Water temperature: MTW

*1: Available when true bearing.

*2: Variation data is required.

*3: True or Relative is changed with menu.

Contents

Main Page i WARNING Radio Frequency Radiation Hazard SAFETY INSTRUCTIONS WARNING CAUTION ii TABLE OF CONTENTS iii SYSTEM CONFIGURATIONS FR-8062/8122 Category of units Antenna unit: Exposed to weather All other units: Protected from weather i v FR-8252 ANTENNA UNIT RSB-0073-087-XN12A/XN13A EQUIPMENT LISTS *: See lists on the back of this manual. Standard Supply vi Optional Supply 1-1 1. MOUNTING 1.1 Antenna Unit Mounting considerations 1-2 Mounting procedure 1-3 STERN CAUTION 1-4 1-5 8. Coat ground terminal and ground point with silicone sealant as shown below. OR Hex nut How to coat ground point and ground termi nal with sili cone s ealant 1-6 1-7 Remove shrink tubing. 2. Remove vinyl sheath approx. 50 mm. Cut vinyl sheath approx. 50 mm. Braided shield Vinyl sheath 1-8 1-9 1-10 1-11 . 1-12 1.2 Display Unit Mounting considerations 1-13 Mounting procedure 1-14 1-15 1.3 Power Supply Unit Page 2-1 2. WIRING 2.1 Standard Wiring 2. WIRING 2-2 2.2 Wiring the Power Supply Unit Cabling 2-3 Jumper block, slide switch setting Power requirement, replacement of fuses 2-4 2.3 Port for External Devices 3-1 3. SETTING UP THE EQUIPMENT 3.1 Setting Language 3-2 3.2 Opening the Installation Menu Basic Settings 3-3 Heading Adjustment 3-4 S S 0 (0 359 ) Auto Installation Setup Tuning Initial Adjust 3-5 Manual Timing Adjust 3-6 Manual MBS Adjust Video Initial Adjust 4-1 4. OPTIONAL EQUIPMENT 4.1 ARP Kit ARP-11 Page 4-3 4.2 External Monitor 4-4 4-5 4.3 Remote Display Page 4-7 4.4 External Buzzer Page RDP-150-J/E A-1 #-: 0#/' 176.+0' &'5%4+26+10%1&' 36; -4 -5 %2 %2 )6: -6 -7 %2 )6: )6: