About storage drawer and cover removal.

GEAppliances.com

Not all features are on all models.

Adjustable Humidity Drawer (on some models)

Slide the control all the way to the HIGH setting to provide high humidity recommended for most vegetables.

Slide the control all the way to the LOW setting to provide lower humidity levels recommended for most fruits.

Drawer and Cover Removal

Drawers can be removed easily by grasping the sides and lifting up slightly while pulling drawers past the stop location.

Full-Width Drawer with

Plastic Cover

To remove the cover, lift it off its supports, pull it forward, tilt it and take it out.

Twin Drawer Shelf

To remove:

1 Remove the drawers.

2 Reach in, push the front of glass cover up, and at the same time, pull it forward as far as it will come.

Tilt it and take it out. Avoid cleaning the cold glass cover with hot water because the extreme temperature difference may cause it to break.

3 Remove the drawer frame. (Always remove the glass cover before you take out the drawer frame.)

Lift the frame off the supports at each side and back, pull it forward, tilt it and take it out.

To replace:

1 Lower the frame until it rests on the supports at each side and back.

2 Replace the glass cover, pushing its rear edge firmly into the rear frame channel and gently lowering the front into place.

3 Replace the drawers.

About the automatic icemaker.

A newly-installed refrigerator may take 12 to 24 hours to begin making ice.

There are 2 types of icemakers:

Power Switch

Icemaker

 

Green Power Light

Feeler Arm

Power switch model

Feeler Arm in the STOP

Feeler Arm in (up) position the ON (down)

position

Feeler arm model

Automatic Icemaker (on some models)

The icemaker will produce approximately 100–130 cubes in a 24-hour period, depending on the freezer compartment temperature, room temperature, number of door openings and other use conditions.

If the refrigerator is operated before the water connection is made to the icemaker, move the feeler arm to the STOP (up) position.

When the refrigerator has been connected to the water supply, move the feeler arm to the ON (down) position.

The icemaker will fill with water when it cools to 15°F. A newly-installed refrigerator may take 12 to 24 hours to begin making ice cubes.

Once the icemaker starts to make ice,

it may take up to 48 hours to fill the bin, depending on the temperature settings and number of door openings.

You will hear a buzzing sound each time the icemaker fills with water.

Throw away the first few batches of ice to allow the water line to clear.

Be sure nothing interferes with the sweep of the feeler arm.

When the bin fills to the level of the feeler arm, the icemaker will stop producing ice.

It is normal for several cubes to be joined together.

If ice is not used frequently, old ice cubes will become cloudy, taste stale, shrink or fuse together.

On power switch models, the green power light will blink if ice cubes get stuck in the icemaker. To correct this, set the power switch to O (off) and remove the cubes. Set the power switch to I (on) to restart the icemaker. After the icemaker has been turned on again, there will be a delay of about 45 minutes before the icemaker resumes operation.

NOTE: In homes with lower-than-average water pressure, you may hear the icemaker cycle multiple times when making one batch of ice.

Icemaker Accessory Kit

If your refrigerator did not already come equipped with an automatic icemaker, an icemaker accessory kit is available at extra cost.

Check the back of the refrigerator for

 

the specific icemaker kit needed for

 

your model.

7

Page 6 Page 8
Page 7
Image 7
GE 17, 18, 16 installation instructions About the automatic icemaker
Page 6 Page 8

16, 17, 18 specifications

General Electric (GE) is known for its longstanding tradition of innovation and engineering excellence, encompassing a wide array of products across various industries. Among its notable offerings are its GE 18, 17, and 16 series of gas turbines, designed for power generation. These turbines exemplify technological advancement, efficiency, and reliability in modern energy production.

The GE 18 series, often referred to as the 7HA.02, is a high-efficiency gas turbine that achieves a thermal efficiency of over 64%. This series utilizes advanced materials and manufacturing processes, enabling it to withstand higher temperatures and pressures, thereby maximizing performance. With its ability to operate on a varied mix of fuels, including natural gas and low heating value gases, the GE 18 series stands out for its versatility. Its modular design simplifies maintenance, allowing for shorter downtimes and enhanced operational availability.

The GE 17 series, known as the 7F.05, offers a robust solution for mid-range power generation. With an efficiency rating around 58%, the 17 series is designed for both simple cycle and combined cycle applications. One of its key features is the incorporation of advanced aerodynamics in its turbine blades, which contributes to lower emissions and higher output. Additionally, the GE 17 series comes equipped with digital technologies, such as GE’s Digital Wind Farm and asset performance management tools, allowing operators to monitor and optimize performance in real time.

The GE 16 series, also called the 9FB, is known for its flexibility and high reliability in power generation. It boasts an efficiency rate of approximately 60% when operated in combined cycle mode. The 16 series is designed for easy integration into existing facilities, making it an ideal choice for upgrades and expansions. Its advanced combustion technology minimizes nitrogen oxide emissions, complying with stringent environmental regulations. Furthermore, the GE 16 series employs advanced sensors and control systems that enhance operational efficiency and safety, ensuring it remains a competitive option in the market.

In summary, GE's 18, 17, and 16 series gas turbines represent the forefront of power generation technology, offering unmatched efficiency, flexibility, and environmental performance. Each series is engineered with unique features to cater to different operational needs, ensuring that GE continues to play a pivotal role in the energy landscape. With ongoing innovations and a commitment to sustainability, GE remains a leader in the gas turbine market.
Top Page Image Contents