GSM2200N

GE Spacemaker® Under-the-Sink Dishwasher

Cabinet Rough-In Dimensions (in inches)

Wall

Cabinet Rough-In Note: Either single- or double-bowl sink may be used, centered or offset, as shown in the front view illustration.

The 20-1/2" maximum dimension from wall to front of sink bowl must be accurate if dishwasher is to fit properly under sink. Water lines to sink faucet and drain from sink can be run through area “A.”

HOT WATER line to dishwasher is installed in area “B.”

Garbage disposer, water lines to faucet, trap, waste air gap and water cutoff valve are installed in 12" wide cabinet shown in area “C.” Sink opening for garbage disposer must be dimensioned as shown in front view, area “C” (7-1/2"). This will provide clearance for the disposer and plumbing in cabinet “C” when using double bowl sink.

If the sink bowl is more than 20-1/2" maximum specified distance form the

Countertop 1-1/2" MIN. thick

10-1/4" MAX.

A

 

 

7-1/2

 

 

FRONT VIEW

C

 

 

6" MAX.

Toe

 

B

kick

 

area

 

 

2412" Floor MIN.

Cabinet Cut-Out for Sink Dimensions (in inches)

Sink

installation cutout

8" x 20" Adjacent

5

cabinet rear cutout

5

 

 

20-1/2" MAX.

 

 

3/4" MIN.

Sink bowl

 

1" MAX. to

11" MINC

 

sink flange

 

Drain L

 

 

 

6" MAX.

 

10-1/4" MAX.

 

 

A

 

1-1/4"

Plumbing depth

 

 

 

 

 

 

MIN. I.R.

 

 

34-1/4

11-3/4"

 

 

± 1/4

MAX. Plumbing

 

Dishwasher

 

 

 

 

 

 

SIDE VIEW

 

 

 

Front of cabinet

 

 

Flange

 

 

 

4" MAX.

B

 

Floor

24"

 

 

 

min. cabinet

 

 

Undersink Dishwasher Wood Insert Dimensions (in inches)

 

 

 

Panel Thickness

Door insert

A

 

 

 

 

 

 

 

 

 

 

 

 

 

3/4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

wall, or if the base cabinet is less than the 24" minimum depth from the wall, a gap between the tub front flange and the front of the base cabinet may result.

Cabinet side

 

adjacent to D/W

3-1/4

FRONT VIEW 11-3/4

12-1/2

 

12

Access insert

C

B

When using GPF325 1/4" custom dishwasher door and access panel kit.

Front

of

Panel

1-1/2 1/2

1/4

When using GPF375 3/4" custom dishwasher door and access panel kit.

Cabinet cutouts for offset single and double bowl sinks. Dishwasher not provided with complete enclosure. Enclosures for sides, top, bottom and back must be provided by installer at time of installation.

Listed by

 

As an Energy Star®

 

partner, GE has determined

Underwriters

 

 

that this product meets the

Laboratories

 

 

Energy Star guidelines

 

 

 

 

for energy efficiency.

Specification Created 4/07

350511

Page 3
Image 3
GE GSM2200N dimensions Cabinet Rough-In Dimensions in inches, Cabinet Cut-Out for Sink Dimensions in inches