Installation Instructions
OPTIONAL CONTROL SETTINGS
The controller display has several options and features.
LOW SALT ALARM |
|
|
|
| |
LEVEL |
|
| |||
|
| SALT |
|
| |
The LOW SALT ALARM, when |
|
|
|
|
|
|
|
|
|
| |
enabled, will sound the beeper |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
| |
when the DAYS TO EMPTY value is |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
| |
15 days or less. To change this setting, press and hold the MODE button for 3 seconds. ON (factory default) or OFF will flash in the display. Press the UP 
or DOWN 
buttons to toggle this feature ON or OFF. Press the MODE button to accept, and the display will move to SALT EFFICIENCY.
SALT EFFICIENCY |
|
|
|
|
|
| SALT |
|
| ||
| LEVEL |
|
| ||
When the SALT EFFICIENCY |
|
|
|
|
|
|
|
|
|
| |
feature is ON, the unit will operate |
|
|
| E |
|
|
|
|
|
| |
|
|
|
|
| |
at a salt efficiency of 4000 grains |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
| |
of hardness removed per pound of salt. This mode of operation is the most efficient setting for salt usage, because the system will tend to recharge more often, with less salt usage. Turning the feature OFF will tend to lengthen the time between recharge cycles, which will provide the most efficient usage of water, but may use more salt . The degree of difference between these two cycles is highly dependent on the water usage and hardness
at a particular installation.
If you have very hard water, and you find your system is regenerating every
NOTE: California Regulations require this feature to be ON for installations in California.
To change the setting, press the UP 
or DOWN 
buttons to toggle the feature ON or OFF. Press the MODE button to accept. The display will move to
SYSTEM/ELECTRONIC DIAGNOSTICS.
SYSTEM/ELECTRONIC | LEVEL |
|
|
| SALT |
|
|
DIAGNOSTICS |
|
|
|
|
|
| |
This display contains system |
|
|
|
diagnostics information to assist in |
|
|
|
|
|
|
troubleshooting problems with the system. See page 17 for details. Press the MODE button to return to the normal run display.
SIGNALS
LOST TIME SIGNAL
If time is lost on the display due to power interruption, the blue indicator light will flash 4 times every second, until the present time of day is entered.
LOW SALT SIGNAL
When the DAYS TO EMPTY drops to 15, the blue indicator light and DAYS TO EMPTY in the display will flash every second and the alarm will beep every 30 seconds (from 8:00 AM to 8:00 PM), to notify the user that the unit is running low on salt. As soon as any button is pressed, the alarm will stop beeping. The blue indicator light and DAYS TO EMPTY will continue to flash. Once salt is added to the brine tank and the SALT LEVEL is reset, the DAYS TO EMPTY will be reset.
ERROR SIGNALS
If there is an error code detected, the blue indicator light will flash 4 times every second, the display will flash Err and the alarm will beep
every 30 seconds (from 8:00 AM to
8:00 PM) to signal that the softener requires service. The alarm can be turned off by pressing any button, but the blue indicator light and display will continue to flash.
See page 17 for information to assist in troubleshooting error codes. Once the problem is corrected, disconnect the transformer from the wall outlet momentarily, and plug it back in. The normal display will appear. The motor may run for several minutes, as the unit resets. If the problem is not corrected, the error code will reappear in 6 minutes.
BLUE INDICATOR LIGHT
Steady blue light indicates that the unit is working correctly. The light flashes when the unit needs attention from the user.
•Light flashes and DAYS TO EMPTY
•Light flashes and Err is in the
•Light will also flash when power to the unit has been interrupted. Check the PRESENT TIME setting.
12