GE JS968TKWW dimensions JS968TK/KK/BK, GE Profile 30 Slide-InElectric Range, KW Rating, 240V

JS968TK/KK/BK

Accessory

Backguard

GE Profile™ 30" Slide-In Electric Range

24

30

A/B*

31-1/4

Dimensions and Installation Information (in inches)

2-7/8"

To Front

Note: Cabinets installed adjacent to slide-in ranges must have an adhesion

Surface Of

KW Rating

Countertop

spec of at least 194° temperature rating.

240V

12.4

Note: 30" ranges conform to U.L. requirements for 0" spacing from adjacent

208V

9.3

walls below countertops. To reduce possibility of scorching walls, engineering

36-1/4

Breaker Size

recommends a minimum of 1-1/2" spacing to allow for possible extended,

20-5/8" Door

high-heat, no-load heating element operation.

Clearance

240V

40 Amps

From Front

Receptacle Locations: For all 30" Slide-In Ranges locally approved flexible

Surface of

Countertop

208V

40 Amps

service cord or conduit must be used because terminals are not accessible

after range installation. See shaded area in drawing for location of electrical

outlet box. Recommended outlet locations allow range to be installed directly against rear wall.

Optional Kits For Slide-In

Body Sides

Optional Lower Trim Kits

25-3/4**

*JXS37 is 5-1/4" and JXS32 is 4"

Electric Ranges

(Slide-in ranges are sold

(If counter height is greater

(excluding handle)

**Total depth from wall to

(Available At Additional Cost)

without sides installed. Can

than 36.5", a lower trim kit

front of closed oven door

including handle is 27-13/16.

be installed on either left

is recommended to extend

Accessory Backguards

or right when unit has one

the useful height to 38"

(Attaches to the back of range

exposed side [no cabinet

maximum)

as a backguard when unit is

Shave Raised Edge To Clear

adjacent]. Kit contains

JXS56WW – White

If you are NOT using the

installed in 30" free-standing

30" Min.

31-1/8" Wide Control Panel

1 body side)

JXS56CC – Bisque

Filler strip or Backguard:

Recommended

Excluding Models JSS28 and JSP39

cutout)

JXS77WW (White)

JXS56BB – Black

6" Min.

JXS32SS (Stainless) - 4" High

JXS77CC (Bisque)

Optional Top Filler Kits

From Walls

9/16

JXS32WW (White) - 4" High

JXS77BB (Black)

JXS32CC (Bisque) - 4" High

JXS66WW – White

23-3/16

Vertical Side Trim Kits

JXS32BB (Black) - 4" High

JXS66CC – Bisque

30"

Min.

(If cabinet cutout width is

JXS66BB – Black

JXS37WW (White) - 5-1/4" High

more than 30", a vertical

30

23-3/16

Acceptable

JXS37CC (Bisque) - 5-1/4" High

side trim kit may be used to

Electrical

13" Max.

JXS37BB (Black) - 5-1/4" High

close the gap between the

If you are using the

Outlet Area

15" Min.

range and cabinet)

Filler strip or Backguard:

JXS86WW (White)

JXS86CC (Bisque)

25

25

JXS86BB (Black)

Installation information: Before installing, consult installation instructions

35-7/8"–38"

packed with product for current dimensional data.

from floor to

30

countertop

2-1/2

For answers to your Monogram,® GE Profile™ or

7-1/2

GE® appliance questions, visit our website at

ge.com or call GE Answer Center® service,

30

2-1/2

800.626.2000.

All GE ranges are equipped with

Listed by

an Anti-Tip device. The installation

Accessor

of this device is an important,

Underwriters

required step in the installation

Laboratories

of the range.

Specification Revised 1/08 220446