Gemini CDX-1250 manual Troubleshooting, Specifications, General, Audio Section

FUNCTIONS: (CONTINUED)

12SINGLE: Pressing the SINGLE button engages SINGLE mode, in this mode the CDX-1250will play one song and then stop. Pressing the

SINGLE button again will then activate CONTINUOUS mode causing the unit to play continuously (after the last track, the unit will return to the first track of the disc and continue to play).

CDX-1250

21TRACK SELECTION: The TRACK SELECTION buttons let you select the track to play. +10 allows you to scan through the track selection

in increments of 10. TRACK SKIP allows you to scan through each track one at a time.

NOTE : ONCE YOU HAVE SKIPPED TO ANOTHER TRACK, YOU MAY NOT GO BACK TO YOUR PROGRAMMED CUE POINT. YOU MUST BEGIN YOUR CUE SELECTION OVER AGAIN, THE CUE WILL BE PRESET TO THE BEGINNING OF THE NEWLEY SELECTED TRACK.

13TIME: The TIME BUTTON switches the time display between three available sources, these three are TIME ELAPSED on the track, TIME

REMAINING on the disc and and TIME REMAINING on the track. TIME ELAPSED indicates how much time has currently gone by since the play button was pressed, TIME REMAING ON DISC will count down the time remaining on the entire disc and TIME REMAINING ON TRACK counts down the time that is left before the end of the track.

14PITCH: Pushing the PITCH button (the button will light up blue) activates the PITCH CONTROL SLIDE. The pitch or speed of the CD will change

plus or minus 12% depending on the position of the PITCH CONTROL SLIDER. Push the PITCH button again to deactivate this mode.

15PITCH CONTROL SLIDE: Moving the PITCH CONTROL SLIDE up or down will lower or raise the pitch percentage + or - 12%.

16PITCH BEND: Pushing the PITCH BEND BUTTONS will automatically raise the pitch up to +16% or lower the pitch down to -16% from the

existing pitch setting. Releasing the buttons will return the pitch

to the original pitch setting. You can use this function to match the beat when mixing from one song to another

17LOOP SECTION: A LOOP repeats the section between the entry point (IN) and the exit point (OUT). To set a loop while the unit is playing,

start by pressing the IN BUTTON (it will light up) and when you reach the desired end loop point press the OUT BUTTON (it will also light up). The loop will continue playing until you press the OUT BUTTON again allowing the music to continue from that point on, to re-engage the loop you must press the RELOOP BUTTON. When you have released your loop the OUT BUTTON will turn OFF and the IN BUTTON will remain lit to indicate that your loop is stored in the CDX-1250memory. Pressing the IN BUTTON again while the unit is playing will erase the previously saved loop while saving your new loop entry point. Press OUT to exit the loop and save a new complete loop. Press RELOOP to return to the beginning of the previously saved loop from normal play. Press RELOOP repeatedly to cause the loop to stutter.

AUX INPUT (MP3): This 1/8” (3.5mm) input accepts any line level

22source including MP3 players, Once a 1/8” (3.5mm) plug is inserted the audio from the CD Player is cancelled out and only the AUX INPUT SOURCE will be heard out of the main outputs.

23MASTER OUTPUT ROTARY KNOB: The MASTER OUTPUT rotary knob adjusts the volume of the MAIN MASTER output.

TROUBLESHOOTING:

-If a disc will not play, check to see if the disc was loaded correctly (label side up). Also check the disc for excessive dirt, scratches, etc.

-If the disc turns but there is no sound, check the cable connections, if they are ok, check your amplifier or reciever.

-If the CD skips, check the CD for dirt or scratches. Do not assume that the CD player is defective. Many cd’s are recorded out of spec and will skip on most or all CD players. Before sending the unit for repair, try playing a CD that you are sure plays properly.

SPECIFICATIONS:

GENERAL:

Type		Compact Disc Player
Disc Type		Standard Compact discs (12 cm & 8 cm)
Time Display		Track Elapsed, Track Remain, or Total remain
Variable Pitch		± 12% Slider with Resume Switch
Pitch Bend		± 16% Maximum
Instant Start		Within 0.03 seconds
Installation		19" each
Dimensions	Main unit: 19" x 3.5" x 10" (482.6 x 88.9 x 254 mm)
Weight Per Unit		Main unit: 5.5 lbs. (2.5 kg)

NOTE: THE FIRST LOOP WILL HAVE A PAUSE AT THE EXIT POINT, WHILE ALL OTHERS WILL BE SEAMLESS.

18PLAY/PAUSE: Each press of the PLAY/PAUSE BUTTON

causes the operation to change from PLAY to PAUSE or from PAUSE back to PLAY. The PLAY/PAUSE BUTTON remains lit when in PLAY mode, while it blinks in PAUSE mode.

19CUE: While the unit is playing and after the cue point has been programmed, pressing CUE will cause the CD player to enter the

PAUSE mode (PLAY/PAUSE BUTTON blinks) at the programmed cue point (the CUE LED is lit). Holding down the CUE button

changes the function to preview , and allows you to stutter start or play from the programmed CUE POINT Releasing the CUE button will return the CD to the preset CUE point.

20STOP BUTTON: When pressed the STOP BUTTON stops the playback of the CD player.

AUDIO SECTION:

Quantization	1 Bit Linear/Channel, 3 Beam Laser
Oversampling Rate	8 Times
Sampling Frequency	44.1 kHz
Frequency Response	20 Hz to 20 kHz
Total Harmonic Distortion	Less Than 0.05%
Signal to Noise Ratio	85 dB
Dynamic Range	85 dB
Channel Separation	85 dB (1 KHz)
Output Level	2.0 +/- 0.2V R.M.S.
Power Supply	AC 115/230V, 60/50 Hz

SPECIFICATIONS AND DESIGN ARE SUBJECT TO CHANGE WITH- OUT NOTICE FOR PURPOSE OF IMPROVEMENT.

5