Page 4
1. Unscrew the outside FADER PLATE SCREWS (B). Do
not touch the INSIDE SCREWS (C).
2. Carefully lift the fader and unplug the CABLE (D).
3. Plug the new fader into the cable and place it back in the
mixer.
4. Screw the fader to the mixer.
7. OUTPUT CONTROL SECTION: The level of the AMP OUT (31) is
controlled by the MASTER (23) slide. The Master TREBLE (20) and
BASS (21) controls allow you to adjust the output of channels 1 - 4.
The BOOTH (27) control adjusts the level of the BOOTH OUTPUT
(30). HINT: The booth output is used by some DJs to run monitor
speakers in their DJ booth. You can also use it as a second ZONE or
AMP output.
NOTE: The RECORD OUT (32) has no level control. The
level is set by the channel slides of the selected channel.
8. TALKOVER SECTION: The purpose of the talkover section is to
allow the program playing to be muted so that the mic can be heard
above the music. The MIC/TALKOVER SWITCH (5) controls MIC 1
and MIC 2 and has three settings. When the MIC/TALKOVER
SWITCH (5) is in the bottom position, MIC 1 and MIC 2 and talkover
are off. When the MIC/TALKOVER SWITCH (5) is in the center
position MIC 1 and MIC 2 are on, the MIC INDICATOR (6) will glow,
but talkover is off. When the MIC/TALKOVER SWITCH (5) is in the
top position, MIC 1 and MIC 2 and talkover will be on and the volume
of all sources except the Mic inputs are lowered by 16 dB. The
TREBLE (2) and BASS (3) controls allow you to fully adjust the tone
of MIC 1 and MIC 2. MIC LEVEL (4) controls the level of MIC 1 and
MIC 2.
9. CUE SECTION: By connecting a set of headphones to the
HEADPHONE (28) jack, you can monitor any or all of the channels.
Press the CUE ASSIGN (18) buttons for channels 1 - 4 to select the
channel or channels to be monitored and their respective LED
indicators will glow. Use the CUE LEVEL (24) control to adjust the
cue volume without effecting the overall mix. By moving the CUE
PGM PAN (22) control to the left you will be able to monitor the
assigned cue signal. Moving the control to the right will monitor the
PGM (program) output. Rotating to the right will monitor the PGM
(program) output.
10.DISPLAY: The DISPLAY (19) indicates the MASTER output left and
right levels.
Specifications
INPUTS:
DJ Mic..........................................................1.5mV 2kOhm balanced
Phono.................................................................................3mV 47kOhm
Line..............................................................................150 mV 27kOhm
OUTPUTS:
Amp/Booth..............................................................0 dB 1V 400ohm
Max..............................20V Peak to Peak
Rec..................................................................................225mV 5kOhm
MIC:
DJ Mic............................................................1.5mV 2KOhm balanced
Bass.............................................................................................± 12dB
High...............................................................................................± 12dB
GENERAL:
Frequency Response............................................20Hz - 20KHz +/- 2dB
Distortion.........................................................................................0.02%
S/N Ratio.........................................................................better than 80dB
Talkover Attenuation.........................................................................-16dB
Headphone Impedance....................................................................16ohm
Power Source.......................................................115/230V 50/60Hz 10W
Dimensions........................................19”w x 4”d x 9”h (483 x 94 x 221 mm)
Weight........................................................................10.17 lbs (4.6 kg)