Introduction
Congratulations on purchasing a Gemini model
Cautions
1.All operating instructions should be read before using this equipment.
2.To reduce the risk of electrical shock, do not open the unit. There are NO USER REPLACEABLE PARTS INSIDE. Please refer servicing to a qualified service technician.
In the U.S.A., if you have any problems with this unit, call
3.Do not expose this unit to direct sunlight or to a heat source such as a radiator or stove.
4.This unit should be cleaned only with a damp cloth. Avoid solvents or other cleaning detergents.
5.When moving this equipment, it should be placed in its original carton and packaging. This will reduce the risk of damage during transit.
6.DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
7.DO NOT USE ANY SPRAY CLEANER OR LUBRICANT ON ANY CONTROLS OR SWITCHES.
Connections
1.This unit comes supplied with a 15 volt AC adaptor. Plug the male pin of the adaptor into the rear panel POWER JACK (7). Then plug the adaptor into a proper power source.
2.Make sure that the POWER (6) switch is in the off position. The POWER LED (12) will be off.
3.To connect the mixer to your amplifier, use the OUTPUT AMP (1) jacks on the rear panel.
4.On the rear panel are 2 stereo PHONO (3, 5) inputs and 2 stereo LINE (2, 4) inputs. The PHONO (3, 5) inputs will accept turntable inputs only. A GROUND (8) screw for you to ground your turntables is located on the rear panel. The stereo LINE (2, 4) inputs will accept any line level input like a CD player or a cassette player.
5.Headphones can be plugged into the front panel mounted HEADPHONE (18) jack.
Operation
1.POWER ON: Once you have made all the equipment connections to your mixer, press the POWER (6) switch. The power will turn on and the POWER LED (12) will glow RED.
2.CHANNEL 1: The CHANNEL LEVEL SLIDE (10) allows you to fully adjust the level of the selected source. The PHONO/LINE (9) switch allows you to select either Line 1 or Phono 1 to play through channel 1.
3.CHANNEL 2: The CHANNEL LEVEL SLIDE (17) allows you to fully adjust the level of the selected source. The PHONO/LINE (16) switch allows you to select either Line 2 or Phono 2 to play through channel 2.
4.CROSSFADER SECTION: The CROSSFADER (15) allows the mixing of one source into another. The left side of the CROSSFADER (15) is channel 1 and the right side is channel 2.
5.CUE SECTION: By connecting a set of headphones to the HEADPHONE (18) jack, you can monitor either channel 1 or channel 2. Select Channel 1 by moving the CUE SWITCH (14) to the left or Channel 2 by moving the CUE SWITCH (14) to the right. Use the CUE LEVEL (13) control to adjust the headphone volume without effecting the overall mix.
6.DISPLAY: The DISPLAY (11) indicates the MASTER (1) output.
Specifications
INPUTS: |
|
|
Phono | 3mV 47Kohm | |
Line | 150 mV 27Kohm | |
OUTPUTS: |
|
|
Amp | 0 dB 1V 400ohm | |
| Max | 10V Peak to Peak |
GENERAL: |
|
|
Frequency Response | 20Hz - 20KHz +/- 2dB | |
Distortion | 0.02% | |
S/N Ratio | better than 80dB | |
Headphone Impedance | 16ohm | |
Power Source | 115V/15V AC 7.5W | |
|
| or 230V/15V AC 7.5W |
Dimensions | 6.5” x 7.5” x 2” (165 x 192 x 53 mm) | |
Weight | 2 lbs (1 kg) | |
Page 2
