Gemini PT-2000 Specifications, Target Light, Xlr Lamp Adaptor, Adjusting The Pitch Control

TARGET LIGHT:

1.Push the TARGET LIGHT SWITCH (20) firmly and the TARGET LIGHT (21) will raise into position and illuminate the stylus tip.

2.To lower the TARGET LIGHT, push down on it until it locks in the casing.

3.When not being used, the TARGET LIGHT should be kept in the lowered position.

XLR LAMP ADAPTOR:

1.Plug a gooseneck light with an XLR base, like the GEMINI GNL- 500, into the XLR LAMP ADAPTOR (22).

2.When the power is turned on, the light will illuminate.

ADJUSTING THE PITCH CONTROL:

1.The PT-2000 is equipped with PITCH CONTROL (23) and QUARTZ LOCK (25). When the QUARTZ LOCK is activated, the PITCH LED (24) lights GREEN, and the speed will be exactly 33 1/3 or 45 RPM depending on which SPEED SELECTOR BUTTON (17) is pushed. PITCH CONTROL automatically disengages when QUARTZ LOCK is activated.

2.When the QUARTZ LOCK is off, you can adjust the PITCH CONTROL(23). When you move PITCH CONTROL (23) off center, the pitch can vary +/- 10% depending on the position of the PITCH CONTROL.

3.Push the QUARTZ LOCK (25) button to bring the speed back to exactly 33 1/3 or 45 RPM when the PITCH CONTROL (23) is positioned off center. Disengaging the QUARTZ LOCK (25) will bring the platter speed back to the original pitch setting.

4.The PLATTER (2) is equipped with a STROBE RPM INDICATOR STRIP (26) and the POWER SWITCH (15) contains built in STROBE LIGHTS (27). When the PLATTER

(2) is spinning, the STROBE LIGHTS illuminate the STROBE RPM INDICATOR STRIP (26). The bottom row of dots will appear to be stationary when the speed of the platter is exactly 45 RPM. The second row from the bottom will appear to be stationary at 33 1/3 RPM.

ARM-LIFT HEIGHT ADJUSTMENT:

If the pre-adjusted distance that the CUE LEVER (18) raises the stylus off the record surface is inadequate, it can be adjusted by turning the ARM-LIFT HEIGHT ADJUSTMENT SCREW (28) while simultaneously pushing down on the TONE ARM (5). Clockwise rotation of the screw will decrease the distance and counterclockwise rotation will increase the distance.

Specifications

TURNTABLE SECTION:

Type	Quartz Direct Drive Manual Turntable
Drive Method		Direct Drive
Motor	Brushless DC Motor 18V
Platter	Aluminum Diecast	11 ½” (332mm) Dia.
	Weight	2 lbs. (0.9 Kg)
Speed		33 1/3 or 45 RPM
Starting Torque		1.5 Kg/cm (1.3 lb/in)
Build-up Characteristics	0.6 sec. standstill to 33 1/3 RPM
Braking System		Electronic Brake
Wow and Flutter		0.01% WRMS*

*This rating refers to the turntable assembly and platter only and excludes effects of records, cartridges or tonearms.

Rumble..............................................................78 dB (IEC 98A WTD)

TONEARM SECTION:

Type	Universal S-Shaped Tubular Arm
Effective Length	9 1/16” (230.1 mm)
Arm Height Adjust Range		0 - 6 mm
Overhang	19/32" (15.2 mm)
Effective Mass	9 g (Without Cartridge)
Offset Angle		22°
Friction	Less Than 7 mg (Lateral, Vertical)
Tracking Error Angle.....Within 2°32' at the outer groove		and within
0°32' at the inner groove of a 30 cm (12") record
Stylus Pressure Adjust Range		0 - 2.5 g
Applicable Cartridge Weight Range		6 - 10 g
Headshell Weight		5.6 g

GENERAL:

Power Supply	115V 60Hz
	or
Power Supply	230V 50Hz
Power Consumption	15 Watts
Dimensions	17 ½” x 6 1/4" x 14"
	444.5mm x 158.75mm x 355.6mm
Weight	25 lbs. (11.34 Kg)

Specifications are subject to change without notice. The weight and dimensions shown are approximate.

Page 6