Gemini Industries UX-1600 Hand Held Transmitter Operation, Lavalier Mic Features, Specifications

Hand Held Transmitter Operation

1.Open the battery holder. Insert 2 AA batteries into the battery holder according to the polarity indication marked on the battery housing. Close the battery holder.

2.Push the power switch to the ON position. The BATT indicator should flash once briefly as you turn on the mic. This indicates that the mic has sufficient power. If BATT stays on, it indicates that the batteries have insufficient power and should be changed. If BATT does not light at all and the mic does not work, it indicates that the batteries are either dead or not positioned correctly. Correct the positioning or change the batteries. If the microphone is not going to be used for any length of time, push the power switch to OFF and remove the batteries. Do not switch the mic on and off rapidly as you will not receive a true BATT indicator reading.

Lavalier Mic Features

•Heavy duty strain relief.

•Foam wind screen.

•Tie clip.

Note: The lavalier mic clip should be placed on the center of your shirt just below your collarbone.

Headset Mic Features

•Heavy duty strain relief.

•Headset.

•Foam wind screen.

Belt Pack Transmitter Operation

1.Open the battery door by sliding towards the arrow. Insert 2 AA batteries into the battery holder as shown on the battery housing. Close the battery door.

2.Connect the mic to the belt pack transmitter.

3.Push the power switch to the ON position. The LOW BATT indicator should flash once as you switch on the belt pack indicating that the transmitter has sufficient power. If LOW BATT stays on, it indicates that the batteries have insufficient power and should be changed. If the LOW BATT does not light at all, it indicates that the batteries are either dead or not positioned correctly. Correct the positioning or change the batteries. If the transmitter is not going to be used for any length of time, push the power switch to OFF and remove the batteries.

4.To adjust the gain (input sensitivity), place the small plastic tool (included with the unit) in the hole marked GAIN on the side of the belt pack. Slowly turn the tool and speak into the mic until the volume is at the desired level. Use of any other tool to adjust the gain will void the warranty.

Hint: If the audio signal is distorted, try turning the gain down on your belt pack transmitter and/or your mixer and increasing the volume output on the receiver.

	Specifications
Receiver:
Frequency Range	790.375~805.375 MHz
Receiving System	PLL Synthesized
Receiving Mode	single channel
Frequency Stability	± 0.005%
Signal to Noise Ratio	> 94 dB @ 15 kHz and 60 dBµV antenna input
Dynamic Range	> 96dB
AF Response	40 Hz - 15 kHz (±3 dB)
T.H.D	< 1.0% @ 1 kHz
Audio Output	unbalanced; 0 dB (0 dB=0.775V)
	at 48 kHz reference RF deviation
	balanced; -20 dB (0 dB=0.775V)
Power Supply	DC 12~18 V
Dimensions	2" (H) x 8.27” (W) x 6.5" (D) (51 x 210 x 166 mm)
Transmitter (all models):
Frequency Range	790.375~805.375 MHz
RF Power Output	30 mW max.
Oscillation Mode	PLL Synthesized
Frequency Stability	± 0.005%
T.H.D	< 0.5% @ 1 kHz
LED Indicator	Power ON-OFF and low battery
Current Consumption	65 mA @ 2.4V
Batteries	2 AA
Transmitter (hand held):
Microphone Element	Dynamic
Dimensions	10.7" (L) x 2.4” (D) (272 x 62 mm)
Transmitter (belt pack):
Microphone Element	Condenser
Dimensions	4" (H) x 2.6” (W) x 1" (D) (98 x 66 x 25 mm)

USA Page 3 USA