8030A Operating Manual

Figure 4: The curves above show the effect of the ‘treble tilt’, ‘bass tilt’

and ‘bass roll-off’ controls on the free field response.

Figure 5: The curve group shows the horizontal directivity characteristics

of the 8030A in its vertical configuration measured at 1m. The lower

curve shows the system’s power response.

Bass amplifier output power with an 8 Ohm load: 40 W
Treble amplifier output power with an 8 Ohm load: 40 W
Long term output power is limited by driver unit
protection circuitry.
Amplifier system distortion at nominal output:
THD < 0.05 %
SMPTE-IM < 0.05 %
CCIF-IM < 0.05 %
DIM 100 < 0.05 %
Signal to Noise ratio, referred to full output:
Bass > 100 dB
Treble > 100 dB
Mains voltage:
100, 120, 220 or 230 V
according to region
Voltage operating range: ±10 %
Power consumption: Idle 10 VA
Full output 80 VA
Lower cut-off frequency, –3 dB: < 55 Hz
Upper cut-off frequency, –3 dB: > 21 kHz
Free field frequency response of system:
58 Hz – 20 kHz (± 2.0 dB)
Maximum short term sine wave acoustic output on axis
in half space, averaged from 100 Hz to 3 kHz:
@ 1m > 100 dB SPL
@ 0.5m > 106 dB SPL
Maximum long term RMS acoustic output in same
conditions with IEC weighted noise (limited by driver
unit protection circuit): @ 1m > 97 dB SPL
Maximum peak acoustic output per pair on top of
console, @ 1 m from the engineer with music material:
> 108 dB
Self generated noise level in free field @ 1m on axis:
< 10 dB (A-weighted)
Harmonic distortion at 85 dB SPL @ 1m on axis:
Freq: 50…100 Hz < 2 %
> 100 Hz < 0.5 %
Drivers: Bass 130 mm (5") cone
Treble 19 mm (3/4") metal dome
Both drivers are
magnetically shielded
Weight: 5.6 kg (12.3 lb)
Dimensions: Height 299 mm (1113/16")
(including Iso-Pod™ table stand)
Height 285 mm (111/4")
(without Iso-Pod™ table stand)
Width 189 mm (77/16")
Depth 178 mm (7")
Connectors:
Input: XLR female, balanced 10 kOhm,
pin 1 gnd, pin 2 +, pin 3 -
Output: XLR male, balanced 100 Ohm
Pin 1 gnd, pin 2 +, pin 3 -
Input level for 100 dB SPL output at 1 m:
-6 dBu at volume control max
Volume control range:
-80 dB relative to max output
Output signal level is 0 dB relative to input signal level
but adjustable by volume control
Crossover frequency, Bass/Treble: 3.0 kHz
Treble tilt control operating range:
0 to –2 dB @ 15 kHz
Bass roll-off control operating in a –6 dB step @ 85 Hz
(to be used in conjunction with a 7050A subwoofer)
Bass tilt control operating range in –2 dB steps:
0 to –6 dB @ 100 Hz
The ‘CAL’ position is with all tone controls set to ‘off’ and
the input sensitivity control to maximum (fully
clockwise).

AMPliFier SecTioNcroSSover SecTioN

SySTeM SPeciFicATioNS

International enquiries:
Genelec, Olvitie 5
FIN-74100, Iisalmi, Finland
Phone +358 17 83 881
Fax +358 17 812 267
Email genelec@genelec.com
In the U.S. please contact
Genelec, Inc., 7 Tech Circle
Natick, MA 01760
Phone +1 508 652 0900
Fax +1 508 652 0909
Email genelec.usa@genelec.com

www.genelec.com

Genelec Document D0036R001. Copyright Genelec Oy 5.2004. All data subject to change without prior notice
In China please contact:
Genelec China Representative Office
SOHO New Town, 88 Jianguo Road
D-1504, Chaoyang District, Beijing 100022, China
Phone +86 10 8580 2180 Fax +86 10 8580 2181
Email genelec.china@genelec.com