![](/images/new-backgrounds/1315374/31537437x1.webp)
SECTION 7: SERVICE
Review the troubleshooting and procedures in this section to fix your machine if a problem develops. If you need replacement parts or you are unsure of your repair skills, then feel free to call our Technical Support at (570)
Troubleshooting
Motor & Electrical
Symptom |
| Possible Cause |
| Possible Solution | |||||
Motor will not start. | 1. | Low voltage. |
|
| 1. | Check power line voltage and correct if necessary. | |||
|
|
|
| 2. | Open circuit in motor or loose connec- | 2. | Inspect all motor connections for loose or open connec- | ||
|
|
|
|
| tions. |
|
|
| tions. |
|
|
|
|
|
| ||||
Motor will not start; | 1. | Short circuit in line cord or plug. |
| 1. | Inspect cord and plug for damaged insulation or shorted | ||||
fuses | or | circuit |
|
|
|
|
| wires. | |
breakers blow. |
| 2. | Short circuit in motor or loose connec- | 2. | Inspect all motor connections for loose or shorted termi- | ||||
|
|
|
| ||||||
|
|
|
|
| tions. |
|
|
| nals or worn insulation. |
|
|
|
| 3. Incorrect fuses | or circuit breakers | in | 3. | Install correct fuses or circuit breakers. | |
|
|
|
|
| power line. |
|
|
|
|
|
|
|
|
|
| ||||
Motor overheats. | 1. | Motor overloaded. |
| 1. | Reduce load on motor. | ||||
|
|
|
|
|
| ||||
Motor stalls (result- | 1. | Motor overloaded. |
| 1. | Reduce load on motor. | ||||
ing in blown fuses | 2. | Short circuit in | motor or loose connec- | 2. | Inspect connections on motor for loose or shorted termi- | ||||
or tripped circuit). |
| tions. |
|
|
| nals or worn insulation. | |||
|
|
|
|
|
|
|
| ||
|
|
|
| 3. | Low voltage. |
|
| 3. | Check power line voltage and correct if necessary. |
|
|
|
| 4. Incorrect fuses | or circuit breakers | in | 4. | Install correct fuses or circuit breakers. | |
|
|
|
|
| power line. |
|
|
|
|
|
|
|
|
|
|
| |||
Machine | slows | 1. | Workpiece pressure is too great. |
| 1. | Reduce workpiece pressure on spindle. | |||
when operating. |
|
|
|
|
|
| |||
|
|
|
|
|
|
| |||
Machine | vibrates | 1. | Machine not secured to workbench. |
| 1. | Secure machine to workbench. | |||
excessively. |
| 2. | Incorrect motor mounting. |
| 2. | Check⁄adjust motor mounting. | |||
|
|
|
|
|
| ||||
Sanding Operations |
|
|
|
| |||||
|
|
|
|
|
|
| |||
Deep |
| sanding | 1. | Sanding sleeve too coarse for the desired | 1. | Use a finer grit sanding sleeve. | |||
grooves or scars in |
| finish. |
|
|
|
| |||
workpiece. |
| 2. Workpiece sanded across the grain. |
| 2. Sand with the grain. | |||||
|
|
|
|
| |||||
|
|
|
| 3. Too much sanding force on workpiece. |
| 3. Reduce pressure on workpiece while sanding. | |||
|
|
|
|
|
|
| |||
Grains | rub off | the | 1. | Sanding sleeve has been stored in an | 1. | Store sanding sleeve away from extremely dry or hot | |||
sanding sleeve. |
|
| incorrect environment. |
|
| temperatures. | |||
|
|
|
| 2. Sanding sleeve has been folded | or | 2. | Store sanding sleeves separately and not folded or flat. | ||
|
|
|
|
| smashed. |
|
|
|
|
|
|
|
|
|
| ||||
Sanding | surfaces | 1. | Too much pressure against sleeve. |
| 1. Reduce pressure on workpiece while sanding. | ||||
clog | quickly | or | 2. | Sanding softwood. |
| 2. | Use different stock. Or, accept the characteristics of the | ||
burn. |
|
|
|
|
|
|
|
| stock and plan on cleaning⁄replacing belts frequently. |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
| ||||
G0538 Oscillating Spindle Sander |
|
|
|