Haier WQP12-CFESS manual Starting the Appliance, Wash Cycle Table, 1/2 Load Button

Starting the Appliance

Starting a wash cycle

After having completed all of the installation steps in the preced- ing paragraphs, turn on the water to the unit, partially open the door of the dishwasher, and press the ON-OFF button "A" lo- cated on the control panel. The "B" indicator light will come on. At this point, the appliance is on and ready to be programmed.

At the end of the wash cycle...

Six beeps will indicate that the wash cycle has finished and the cycle indicator light “F” will begin to extinguish. Open the door, turn off the appliance using the ON/OFF switch and turn off the water supply to the unit. Wait a few minutes before removing the dishes so as to avoid handling them while still hot (when they are more susceptible to breakage) and to get better drying results.

Wash Cycle Table

Cycle	Cycle	Description of	Detergent	Rinse Aid
	Selection
		Cycle
	Information

Setting and Starting a wash Cycle

Choose the desired cycle by pressing the cycle selection button "G". Each time it is pressed, the cycle indicator lights "F" will change to indicate the cycle selected.

Choose the wash cycle you feel is most appropriate for the type of dishes that need washing (consult the wash cycle table con- tained in this manual, especially when first using the appliance). Close the door and after a few seconds, The wash cycle will begin. Read the paragraph entitled, "Cancelling or changing a cycle while underway. "The end of the cycle will be signalled by six beeps, and the indicator light "F" will extinguish.

Cancelling or changing a cycle while underway...

Setting The Start Delay Time

Open the door of the dishwasher partially. Press button "J" (see, Close-up View" Control Panel") to delay the starting time for a wash cycle.

.1st press, “2h” indicator comes on, the cycle will start in 2 hours.

.2nd press, “4h” light indicator comes on, the cycle will start in 4 hours.

.3rd press, “6h” light indicator comes on, the cycle will start in 6 hours.

.4th press, “2h” and “6h” light indicators come on, the cycle will start in 8 hours.

.5th press, “4h” and “6h” light indicators come on, the cycle will start in 10 hours.

.6th press, “2h” , “4h” and “6h” light indicators come on, the cycle will start in 12 hours.

Very dirty dishes, pots and pans. (Not to be used with deli- cate items)

Heavy Duty (IEC-EN50242)

Normal dirty dishes, pots and pans. Stan- dard daily cycle.

Normal Wash

Normal dirty dishes, pots and pans without dried on residue.

Pre-wash with cold water.
Extended wash at 56
Rinse with cold water.	30g
Rinse with hot water
Drying.
Pre-wash with cold water.
Extended wash at 56 .
Rinse with cold water.	30g
Rinse with cold water.
Rinse with hot water.
Drying.
Pre-wash with cold water.
Extended wash at 56
Rinse with cold water.	30g
Rinse with hot water

Premise: A cycle that is underway can only be changed if it has only been running for a short time.

Otherwise, the detergent may have already been used, and the appliance may have already drained the wash water. If this is the case, the detergent dispenser must be refilled (see the paragraph entitled, "Loading the Detergent").

To change the cycle currently underway, open the door, press the "G" programming button and hold it in for about 5 seconds. Once the cycle has been cancelled, the dishwasher will emit a short acoustic sound and the relative indicator light will turn off.

To set a new wash cycle, follow the instructions contained in the paragraph entitled, "Setting and Starting a Wash Cycle."

.last press, all light indicators will extinguish and you can reset. After selecting the delay time, the wash cycle can be set, as explained in "Starting a wash cycle..." There will be a short acous- tic signal, and at this point the delay period will begin to count down. During this period the delay indicator light (I) will blink. At the end of the delay time, the indicator will stop blinking and the cycle will start.

NOTE:

a)During the delay period, none of the settings can be modified. If necessary, they can be cancelled by pressing cycle selector "P" for about 5 seconds.

b)If the power to the appliance goes off or the door is opened during the delay period, the clock will stop the countdown. It will start again when the power has come back on, or when the door has been closed.

Wash Cycle Adjustment Buttons

1/2 Load Button

This button (see" Close-up View-Control Panel", letter "C") makes it possible to wash dishes using only the upper rack if there are not enough dishes for a full load, This will allow you to save on water and electrical energy.

It cannot be used with the heavy duty wash cycles.

Light Wash

Glassware

Rapid Wash

Rinse

Heat wash

Economic, fast cycle to be used for delicate items which are sensitive to higher. Run immediately after dishes are used.

Economic, fast cycle to be used to on not very dirty dishes right after they are used. No dry- ing cycle.

Pre-wash of dishes, pots and pans while waiting for the load to be completed after the subsequent meal.

The cycle of heat wash- ing and dry tableware.

Drying.
Wash at 58 .
Rinse with warm water.	15g
Hot rinse.
Drying.

Short wash at 40 .	15g
Cold rinse.

Short cold wash to prevent

food residue from drying on the dishes

Heat washing.

.5. .6.