Specific Safety Instructions

1.Operators and others in work area MUST wear ANSI-approved safety goggles with side shields during use. The employer is responsible to enforce the use of eye protection by the operator and others in the work area.

2.Keep fingers away from trigger when not driving fasteners to avoid accidental firing.

3.Choice of triggering method is important. Check manual for triggering options.

4.Always assume the tool contains fasteners.

5.Do not point the tool toward yourself or anyone whether it contains fasteners or not.

6.Do not actuate the tool unless the tool is placed firmly against the workpiece.

7.Respect the tool as a working implement.

8.No horseplay. This tool is not a toy and can be deadly if misused.

9.Do not load the tool with fasteners when any one of the operating controls, such as the Trigger or Safety Nosepiece, is activated.

10.Do not remove, tamper with, or otherwise cause the tool operating controls to become inoperable.

11.Do not operate the tool if any portion of the tool operating controls is inoperable, disconnected, altered, or not working properly.

12.Disconnect the tool from the air supply when:

a.Unattended.

b.Performing any maintenance or repair.

c.Clearing a jam.

d.Moving the tool to a new location.

13.Do not make any modifications to this tool.

14.Refer to the tool maintenance instructions for detailed information on the proper maintenance of the tool.

15.Fire fasteners into an appropriate work surface only. Do not attempt to fire fasteners into surfaces too hard to penetrate. Do not drive fasteners on top of other fasteners, or at too steep of an angle. Fasteners can ricochet causing personal injury.

16.Do not fire fasteners too close to the edge of

aworkpiece. They may split the workpiece

and fly free, causing personal injury.

17.Keep clear of the workpiece near the area being fastened. Fasteners may bend sideways during firing, causing them to exit the workpiece at an unexpected point, causing personal injury.

18.Transport tool safely. Always disconnect air supply when moving the tool. Carry the tool by the handle and avoid contact with the trigger.

19.Hold tool away from head and body. During operation the tool may kick back causing injury.

20.Do not fire fasteners into a workpiece that has people, utility lines, or other objects behind or inside it.

21.Keep balance while using this tool.

Keep area below clear if working in an elevated location, and secure air hose to prevent falls from bystanders accidentally pulling on it.

22.Obey the manual for the air compressor used to power this tool.

23.Install an in-line shutoff valve to allow immediate control over the air supply in an emergency, even if a hose is ruptured.

24.Do not engrave or stamp anything into the housing to avoid weakening it.

25.WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities, contains chemicals known [to the State of California] to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

•Lead from lead-based paints

•Crystalline silica from bricks and cement or

other masonry products

• Arsenic and chromium from chemically treated lumber

Your risk from these exposures varies, depending on how often you do this type of work.

To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. (California Health & Safety Code § 25249.5, et seq.) WARNING: The brass components of

this product contain lead, a chemical known to the State of California to cause birth defects (or other reproductive harm). (California Health & Safety code § 25249.5, et seq.)

26.The warnings and precautions discussed in this manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.

SAFETY

SETUP

OPERATION

MAINTENANCE

Item 68028	For technical questions, please call 1-800-444-3353.	Page 5
68068

68068 specifications

Harbor Freight Tools 68068 is a powerful and versatile tool that caters to both DIY enthusiasts and professional tradespeople alike. Known for its affordability and robust design, this tool has gained a reputation for reliability and efficiency.

One of the standout features of the Harbor Freight Tools 68068 is its high output. Equipped with a powerful motor, it delivers consistent performance across various applications. Whether you’re cutting, grinding, or polishing, this tool is designed to handle demanding tasks with ease. Its ability to reach high speeds allows users to complete jobs quickly and effectively, making it a highly sought-after addition to any workshop.

The 68068 also incorporates advanced technology to enhance user experience and safety. It features a user-friendly interface with easily accessible controls, allowing for seamless operation. Additionally, it is designed with an ergonomic grip that ensures comfortable handling, reducing user fatigue during prolonged use. This thoughtful design is crucial for professionals who rely on this tool for extensive periods.

Another key characteristic of the Harbor Freight Tools 68068 is its durability. Constructed from high-quality materials, this tool is built to withstand the rigors of daily use. Its rugged exterior not only protects the internal components but also ensures longevity, making it a cost-effective choice for users who demand reliability over time.

Versatility is another significant advantage of the 68068. It comes with an array of attachments and accessories that allow users to switch between different tasks effortlessly. From sanding and buffing to cutting and drilling, the capability to adapt to various applications makes it a must-have tool for any toolbox.

Moreover, the Harbor Freight Tools 68068 comes with a comprehensive warranty, reflecting the manufacturer’s confidence in its quality and performance. This assurance provides peace of mind for buyers, knowing that their investment is protected against defects and issues.

In conclusion, the Harbor Freight Tools 68068 is a feature-packed tool that offers power, durability, and versatility. With its user-friendly design, advanced technology, and array of capabilities, it serves as an indispensable asset for both hobbyists and professionals. Whether tackling home improvement projects or professional jobs, the 68068 ensures that users have the right tool to get the job done efficiently and effectively.

Harbor Freight Tools 68068 owner manual Specific Safety Instructions

Models: 68068