Hearth and Home Technologies A36C, A36CH, A42C, A42CH DO NOT DISCARD

48

– NOTES –

E. Contact Information

DO NOT DISCARD THIS MANUAL

CAUTION

• Important operating

and maintenance

instructions included.

• Leave this manual with

party responsible for

use and operation.

• Read, understand

and follow these

instructions for safe

installation and

operation.

DO NOTDISCARD

This product may be covered by one or more of the following patents: (United States) 4593510, 4686807, 4766876,

4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983,

5429495, 5452708, 5542407, 5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237,

5947112, 5996575, 6006743, 6019099, 6048195, 6053165, 6145502, 6170481, 6237588, 6296474, 6374822, 6413079,

6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940,

6748942, 6769426, 6774802, 6796302, 6840261, 6848441, 6863064, 6866205, 6869278, 6875012, 6880275, 6908039,

6919884, D320652, D445174, D462436; (Canada) 1297749, 2195264, 2225408, 2313972; (Australia) 780250, 780403,

1418504 or other U.S. and foreign patents pending.

Heatilator • A36C & A42C • 28396 • Rev AG • 11/08

Hearth& Home Technologies Inc.

1915W. Saunders Street

Mt.Pleasant, Iowa 52641

www.heatilator.com

Please contact your Heatilator dealer with any questions or concerns.

For the number of your nearest Heatilator dealer, please visit www.heatilator.com.

Contents

Main Owners Manual Models: A36C, A36CH A42C, A42CH WARNING NOTICE DO NOT DISCARD Homeowner Reference Information FIREPLACE NO. Listing Label Information/Location Congratulations! MODEL NO. MODEL NO. MFG. DATE ! Table of Contents User Guide Installer Guide Hearth & Home Technologies LIMITED WARRANTY Warranty Page 1 B. Non-Combustible Materials C. Combustible Materials A. Appliance Certi cation 2 A. Your Fireplace User Guide WARNING C. Starting a Fire B. Seasoned Wood D. Grate E. Firescreen F. Flue Damper I. Outside Air (optional) J. Fan Kit (optional) H. Glass Doors K. Vented Gas Log Sets & Gas Log Lighters L. Optional Components N. Wood Fuel Hardwood vs Softwood Moisture Storing Wood Seasoned Wood 3 A. Disposal of Ashes B. Chimney Inspection/Cleaning Creosote - Formation and Need for Removal C. Check Firebox Refractory D. Inspect Grate E. Glass Cleaning 4 Start Fire Problems Possible Cause Solution 5 A. Typical Fireplace System Installer Guide D. Negative PressureB. Design and Installation Considerations C. Draft E. Locating Fireplace & Chimney F. Tools and Supplies Needed H. Inspect Fireplace and Components G. Typical Fireplace System 6 A. Select Fireplace Location B. Clearances Note: Chimney air kit not shown, but required in Canada. B A D D. Frame the Fireplace C A 2 in. (51 mm) min. air space clearance from chimney. Header MUST NOT be notched! C. Sidewalls/Surrounds 7 A. Things to Consider B. Position the Fireplace C. Place Protective Metal Hearth Strips D. Level Fireplace 3 ft min. from top of uppermost chimney section to air inlet. Note: Chimney air kit not shown, but required in Canada. E. Install Outside Air Kit 8 A. Chimney Requirements Table 8.1 Table 8.2 B. Using Offsets/Returns C. Assembling Chimney Sections D. Install Chimney Air Kit E. Installing Ceiling Firestops F. Installing Attic Insulation Shield H. Complete Installation The following steps should be skipped if using a chase. I. Install Flashing G. Cut out Hole in Roof J. Chimney Termination Requirements 9 A. Construct the Chase B. Install Fireplace & Chimney C. Install Chase Top D. Install Termination Cap TR342 Round Telescoping Termination Cap Install the chimney sections up through the chase enclo- sure. ST375 Square Termination Cap Figure 9.4 Installing a TR344 Round Termination Cap European Copper Series Termination Cap Figure 9.7 Installing a TS345/TS345P Square Termination Cap TCT375 Terra Cotta Cap TS345/TS345P Square Termination Cap Figure 9.8 Installing a TCT375 Terra Cotta Cap European Copper Series Termination Cap Figure 9.9 Installing an Adapter for European Copper Cap Se- ries (CT-King shown) 10 Open Top Shroud (TR342 & TR11/TR11T caps require radiation shield) A. Radiation Shield B. Field Constructed Shrouds 3 in. (76 mm) Min. Opening Height Min. Base Dim Roofed Style Shroud (radiation shield required) Min. Height above radiation shield Min. Base Dim 3 in. (76 mm) Min. Radiation Shield Height from top of Chase Min. Opening Width Mailbox Style Shroud (radiation shield required) 11 11 R = 1/k x inches of thickness Table 11.2 A. Non-Combustible Materials D. Finishing Material E. Combustible Mantel B F. Sidewalls/Surrounds A 12 in. [305 mm] 9 3/4 in. [248 mm] 12 in. [305 mm] 12 12 A. Gas Log/Lighter Provision B. Wood Burning Inserts C. Install Fan 13 13 A. Fireplace Dimensions B. Fireplace Components 16 in. (406 mm) Heatilator A36C & A42C 28396 Rev AG 11/08 52 in. (1321 mm) 1/2 in. (13 mm) 20 in. (508 mm) C. Chimney Components ID4 Insulated Duct i UD4 Uninsulated Duct 42 in. (1067 mm) A B14-1/2 in. (368 mm) A Catalog # B C D ABCD E D A D. Service Parts A36C, A36CH Herringbone Brick Pattern 11 11 Traditional Brick Pattern D. Service Parts (continued) A42C, A42CH Herringbone Brick Pattern 11 11 Traditional Brick Pattern NOTES E. Contact Information DO NOT DISCARD THIS MANUAL CAUTION DO NOT DISCARD