Hearth and Home Technologies GDST5244I, GDST5244IL

Heatilator • GDST5244I • 4045-127 • Rev W • 11/0824

4 ft min.

(1.22 m)

25 ft max.

(7.62 m)

H1V1

Installed

Horizontally

Installed

Vertically

Figure 7.5

Two Elbows

1. Top Vent - Horizontal Termination - (continued)

Figure 7.4

Two 45° Elbows replacing One 90° Elbow

V1 min. V1 max. H1+H2 max. H1+H2+H3 max.

ft mftmftmftm

1.5 0.46 - - 18 5.49 18 5.49

2 0.61 - - 25 7.62 25 7.62

- - 25 7.62 25 7.62 25 7.62

Contents

Main Owners Manual CAUTION Listing Label Information/Location A. Congratulations Model # XXXXXXXXX Serial # Gas Type Orifice Size Safety Alert Key: Table of Contents 1 Listing and Code Approvals User Guide 2 Operating Instructions 3 Maintenance and Service Page B. Warranty Hearth & Home Technologies LIMITED WARRANTY B. Warranty (continued) 1 B. Tempered Glass Speci cations C. BTU Speci cations E. Non-Combustible Materials Speci cation F. Combustible Materials Speci cation 1 A. Appliance Certi cation G. Electrical Codes H. Requirements for the Commonwealth of Massachusetts Installation of Carbon Monoxide Detectors Approved Carbon Monoxide Detectors Signage Inspection 2 B. Your Fireplace A. Gas Fireplace Safety User Guide D. Clear Space C. Fan Kit (optional) F. Fixed Glass Assembly E. Decorative Doors and Fronts G. Remote Controls, Wall Controls and Wall Switches LIGHTING INSTRUCTIONS TO TURN OFF GAS TO APPLIANCE NATURAL GAS CAUTION: WARNING: J. After Fireplace is Lit K. Frequently Asked Questions 3 Glass Cleaning 3 A. Maintenance Tasks-Homeowner Remote Control Venting Control Compartment and Firebox Top B. Maintenance Tasks-Quali ed Service Technician Logs Firebox Gasket Seal and Glass Assembly Inspection Burner Ignition and Operation 4 Installer Guide 4 A. Typical Appliance System B. Design and Installation Considerations D. Inspect Appliance and Components C. Tools and Supplies Needed 5 A. Select Appliance Location B. Construct the Appliance Chase C. Clearances D. Mantel and Wall Projections Mantel Legs or Wall Projections Mantels 6 A. Vent Termination Minimum Clearances 6 Gas, Wood or Fuel Oil Termination Cap Minimum DV = 20 in. BV = 8 ft B Gas Termination Cap ** A * Perpendicular Wall S min T 7 A. Approved Pipe C. Use of Elbows 7 B. Vent Table Key D. Measuring Standards H V E. Vent Diagrams 1. Top Vent - Horizontal Termination One Elbow Page Installed Vertically 2. Top Vent - Vertical Termination No Elbow Two Elbows Install Flue Restrictor Page 8 A. Pipe Clearances to Combustibles 8 B. Wall Penetration Framing Combustible Wall Penetration Non-Combustible Wall Penetration C. Install the Ceiling Firestop D. Install Attic Insulation Shield Flat Ceiling Installation Vaulted Ceiling Installation 9 A. Secure and Level the Appliance 10 10 A. Assemble Vent Sections (DVP Only) Attach Pipe to the Firebox Assembly Assemble Pipe Sections B. Assemble Vent Sections (SLP Only) Commercial, Multi-family (Multi-level exceeding two stories), or High-Rise Applications C. Assemble Slip Sections E. Disassemble Vent Sections D. Secure the Vent Sections F. Install Decorative Ceiling Components (SLP only) G. Install Metal Roof Flashing Caulk Pipe Flashing H. Assemble and Install Storm Collar I. Install RF4-8 SLP-FS Secure with 4 screws no longer than 1/2 in./13 mm The SLP-FS shown in this photo will not be used with DVP pipe. Apply Sealant Top & Partial Sides K. Install Decorative Wall Components (SLP only) L. Heat Shield Requirements for Horizontal Termination Screws Caulk J. Install Vertical Termination Cap M. Install Horizontal Termination Cap 11 A. Fuel Conversion B. Gas Pressure C. Gas Connection 11 12 A. Wiring Requirements B. Intelli re Ignition System Wiring C. Optional Accessories Requirements 12 E. Junction Box Installation F. Wall Switch Installation for Fan (Optional) 13 13 A. Mantel and Wall Projections Mantels Mantel Legs or Wall Projections 14 A. Remove Fixed Glass Assembly B. Remove the Shipping Materials C. Clean the Appliance D. Accessories Page K. Air Shutter Setting H. Fixed Glass Assembly Closed J. Install Trim and/or Surround F. Place the Rockwool 15 15 A. Intelli re Ignition System Intelli re Ignition System - (continued) 16 16 A. Appliance Dimension Diagram B. Vent Components Diagrams Assembled Height: 24 in./610 mm Diameter: 10 in./254 mm DVP-AS2 26 in. (660 mm) Page Page Fillers Page SL-2DVP Adapter 13 in. (330 mm) 15 in. (381 mm) 8-1/8 in. (206 mm) SLP-HRC-SS Heatilator GDST5244I 4045-127 Rev W 11/08 57 C. Service Parts Log Set Assembly Part number list on following page. at Depot C. Service Parts (continued) IPI Valve Assembly Heatilator GDST5244I 4045-127 Rev W 11/0858 at Depot D. Optional Components Optional Accessories (shipped separately) NOTICE