Hearth and Home Technologies I100 3

11

3

3 Maintainance and Service

Figure 3.1 Chimney & Termination Cap Cleaning

A. Disposal of Ashes

Frequency: When they reach bottom of grate

By: Homeowner

WARNING! Risk of Fire! Ashes could contain hot em-

bers.

• Place ashes in a metal container with a tight-ﬁ tting lid.

• The closed container should be placed on a

noncombustible ﬂ oor or on the ground, well away from

all combustible materials, pending ﬁ nal disposal.

• If the ashes are disposed of by burial in soil or otherwise

locally dispersed, they should be retained in the closed

container until all cinders have thoroughly cooled.

B. Chimney Inspection/Cleaning

Frequency: At least twice a year during heating season

or as recommended by a certiﬁ ed chimney sweep

By: Certiﬁ ed chimney sweep

WARNING! Risk of Fire! Ignited creosote is extremely

HOT. Prevent creosote buildup.

Refer to Figure 3.1 to remove/reinstall termination caps.

Creosote - Formation and Need for Removal

When wood is burned slowly, it produces tar and other

organic vapors, which combine with expelled moisture to

form creosote. The creosote vapors condense in the rela-

tively cool chimney ﬂ ue of a slow-burning ﬁ re. As a result,

creosote residue accumulates on the ﬂ ue lining. When

ignited this creosote makes an extremely hot ﬁ re.

WARNING! Risk of Fire! A chimney ﬁ re can permanently

damage your chimney system and nearby structures.

In the event of a chimney ﬁ re, Hearth & Home Technolo-

gies Inc. recommends

• replacement of the chimney, and

• inspection of the adjacent structure to the provisions of

NFPA Level III inspection criteria.

The chimney shall be inspected at least twice a year

during the heating season to determine when a creosote

buildup has occurred.

When creosote has accumulated it shall be removed to

reduce the risk of a chimney ﬁ re.

Heatilator • I100 • 35144 • Rev AA • 11/08

Chimney

Remove 4 screws

and lift top pan off.

Cap

Slip

Section

ST1175

Square Termination Cap

Cap

Remove screws,

lift top cover. Top Cover

TR11/TR11T

Round Termination Cap TCT1175

Terra Cotta

Termination Cap

Remove 2 screws from

the front and back and

lift the top off.

Contents

Main Owners Manual Models: I100 WARNING NOTICE DO NOT DISCARD Homeowner Reference Information FIREPLACE NO. Listing Label Information/Location Congratulations! MODEL NO. MODEL NO. MFG. DATE ! Table of Contents User Guide Installer Guide Hearth & Home Technologies LIMITED WARRANTY Page 1 B. Non-Combustible Materials C. Combustible Materials A. Appliance Certi cation 2 A. Your Fireplace User Guide WARNING C. Starting a Fire B. Seasoned Wood D. Grate E. Firescreen F. Flue Damper I. Outside Air (optional) H. Glass Doors J. Vented Gas Log Sets & Gas Log Lighters K. Optional Components L. Clear Space M. Wood Fuel Hardwood vs Softwood Moisture Storing Wood Seasoned Wood 3 A. Disposal of Ashes B. Chimney Inspection/Cleaning Creosote - Formation and Need for Removal C. Check Firebox Refractory D. Inspect Grate E. Glass Cleaning 4 Start Fire Problems Possible Cause Solution 5 A. Typical Fireplace System Installer Guide D. Negative PressureB. Design and Installation Considerations C. Draft E. Locating Fireplace & Chimney F. Tools and Supplies Needed H. Inspect Fireplace and Components G. Fireplace System Requirements 6 A. Select Fireplace Location B. Clearances (roof) Grid represents inch scale. D. Frame the Fireplace C. Sidewalls/Surrounds 7 A. Things to Consider B. Unpack the Refractory & Fireplace C. Position the Fireplace D. Place Protective Metal Hearth Strips E. Level Fireplace F. Install Refractory 3 ft min. from top of uppermost chimney section to air inlet. G. Install Outside Air Kits Page 8 A. Chimney Requirements Table 8.1 Table 8.2 B. Using Offsets/Returns C. Assemble Chimney Sections D. Install Chimney Air Kit E. Install Ceiling Firestops F. Install Attic Insulation Shield H. Complete Installation The following steps should be skipped if using a chase: I. Install Flashing G. Cut out Hole in Roof J. Chimney Termination Requirements 9 A. Construct the Chase B. Install Fireplace & Chimney D. Install Termination Cap C. Install Chase Top 36 Heatilator I100 35144 Rev AA 11/08 Do NOT block air holes Figure 9.7 Installing a TCT1175 Terra Cotta Cap ST1175 Square Termination Cap TR11T Round Telescoping Termination Cap 10 Open Top Shroud (TR11/TR11T caps require radiation shield) A. Radiation Shield B. Field Constructed Shrouds 3 in. (76 mm) Min. Opening Height Min. Base Dim Roofed Style Shroud (radiation shield required) Min. Height above radiation shield Min. Base Dim 3 in. (76 mm) Min. Radiation Shield Height from top of Chase Min. Opening Width Mailbox Style Shroud (radiation shield required) 11 11 R = 1/k x inches of thickness Table 11.2 A. Non-Combustible Materials Raised Hearth Extension Framing Non-combustible Sealant Flush Hearth Extension Framing D. Finishing Material E. Combustible Mantel Grid represents inch scale. 12 12 A. Gas Log/Lighter Provision B. Wood Burning Inserts 13 13 A. Fireplace Dimensions B. Optional Components See your Heatilator Dealer for a complete list of optional components. B. Chimney Components ID4 Insulated Duct i UD4 Uninsulated Duct 42 in. (1067 mm) 25-1/4 in. (641 mm) 29 in. (737 mm) 15-1/4 in. (387 mm) A Catalog # B C D ABCD E D A D. Service Parts Service Parts Heatilator I100 35144 Rev AA 11/08 ITEM DESCRIPTION COMMENTS PART NUMBER 50 in. Woodburning Fireplace NOTES E. Contact Information DO NOT DISCARD THIS MANUAL CAUTION DO NOT DISCARD