Manuals / Hearth and Home Technologies / Household Appliance / Indoor Fireplace

Hearth and Home Technologies T4200 Mark the Exit Point of the Roof, Cut out the Hole in the Roof

Models: T4200

1 28
Download 28 pages 63.75 Kb
Page 16
Image 16

T4200 FIREPLACE INSTALLATION INSTRUCTIONS

9.Mark the Exit Point of the Roof

Locate the point where the chimney will exit the roof by plumbing down to the center of the chimney. Drive a nail up through the roof to mark the center. See Figure 14.

10.Cut out the Hole in the Roof

Measure to either side of the nail and mark the 17” x 17” or 17” x 26” opening required. This is measured on the horizontal; actual length may be larger depending on the pitch of the roof. Cut out and frame the opening. See Chapter 25 of the Uniform Building Code for roof framing details.

Be sure to maintain a 2” minimum air space between the chimney section and the roof.

11.Assemble the Chimney Sections Through the Roof

Continue to add chimney sections through the roof opening, maintaining at least a 2” air space.

12.Install the Roof Flashing

If a roof flashing is to be used, install the roof flashing appropriate to the roof pitch and install a round termination cap following the instructions shipped with the cap.

For chase installations you can use a round termination cap (TR11), a round telescoping termination cap (TR11T) or a square termination cap (ST1175). A chase installation must use a chase top. Chase tops are available from your Heatilator distributor. See page 20 for building a chase.

13.Install the Outside Air Kit

The outside air kit is supplied as a standard feature with this fireplace and its use is highly recommended to minimize the effects of negative pressure within the structure. It is recommended to utilize the shortest duct run to optimize the performance of the outside air kit. The outside air kit inlet thimble should be positioned at least four feet above the ground level, in a manner that will not allow snow, leaves, etc. to block the inlet.

The outside air kit is installed on the left hand side of the fireplace. Remove the cover plate from the side of the fireplace assembly where the air kit is to be installed. See Figure 15 for handle location/operation.

14.Install the Chimney Air Kit

When installing the chimney air kit, follow the instructions provided with this accessory.

Figure 14 - Ceiling/Attic Construction

Figure 15 - Air Kit Handle Location

CAUTION:

The air kit handle may get hot while burning the fireplace. Use care when operating the handle.

16

35036 Rev E

12/03

Page 15 Page 17
Page 16
Image 16
Hearth and Home Technologies T4200 manual Mark the Exit Point of the Roof, Cut out the Hole in the Roof
Page 15 Page 17

T4200 specifications

Hearth and Home Technologies T4200 is a remarkable addition to modern home heating solutions, designed to enhance comfort and efficiency while maintaining aesthetic appeal. With its advanced features and cutting-edge technologies, the T4200 offers homeowners a perfect balance of warmth, style, and environmental consciousness.

One of the standout features of the T4200 is its impressive heating capacity. With a BTU output capable of heating large spaces, this unit ensures that homes remain cozy even during the coldest months. The well-designed combustion system optimizes fuel usage, resulting in enhanced efficiency and reduced emissions, making it an environmentally friendly choice for homeowners.

The T4200 boasts a sleek and contemporary design, fitting seamlessly into various interior styles. Its large viewing window provides an unobstructed view of the flames, creating a captivating ambiance that traditional heating methods often lack. The unit can be customized with a range of options, including different trim styles and finishes, allowing homeowners to personalize their heating solution to match their décor.

Equipped with state-of-the-art technology, the T4200 features an advanced control system that allows users to easily manage heat output and flame intensity. Many models include a remote control and programmable thermostat, giving homeowners the convenience of adjusting settings from anywhere in the room. This level of control not only enhances comfort but also contributes to energy savings.

Safety is a top priority in the T4200's design. It incorporates built-in safety features such as automatic shut-off systems, which activate in the event of malfunctions. Additionally, the unit is constructed from durable materials designed to withstand high temperatures, ensuring longevity and reliability.

The T4200 is designed with versatility in mind. It can operate on various fuel types, including natural gas, propane, or wood, catering to the preferences of diverse customers. This flexibility further enhances its appeal as an all-around heating solution.

Overall, the Hearth and Home Technologies T4200 stands out as a leader in the home heating market. Its combination of high performance, innovative technology, and stylish design make it an ideal choice for those seeking efficient and attractive heating options. Homeowners can enjoy the warmth and beauty of this unit, knowing they have invested in a long-lasting and environmentally conscious heating solution.