Heat & Glo LifeStyle CERONA-36, CERONA-42

Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. F • 04/08 57

C. Service Parts CERONA-36

Beginning Manufacturing Date: June 2006

Ending Manufacturing Date: ______

Service Parts Diagram

Part number list on following page.

Log Set Assembly

Contents

Main CERONA-36 CERONA-42 Owners Manual DO NOT DISCARD Congratulations Listing Label Information/Location Homeowner Reference Information Table of Contents 1 B. BTU Speci cations 1 A. Appliance Certi cation D. Non-Combustible Materials Speci cation E. Combustible Materials Speci cation C. High Altitude Installations F. Requirements for the Commonwealth of Massachusetts 2 A. Design and Installation Considerations 2 C. Inspect Appliance and Components B. Tools and Supplies Needed 3 A. Selecting Appliance Location B. Constructing the Appliance Chase C. Clearances D. Mantel Projections B A mm mm Note: If using the Apollo Mantel System, the appliance must be raised 1-1/4 in. from oor . E. Hearth Extension 4 A. Vent Termination Minimum Clearances Measure horizontal clearances from this surface. 4 Measure vertical clearances from this surface. Figure 4.2 speci es minimum vent heights for various pitched roofs. V = VENT TERMINAL X Alcove Applications B. Continue Adding Vent Components C. Install Support Brackets 5 B. Use of Elbows 5 8-1/2 in. Horizontal A. Vent Table Key C. Measuring Standards H V V H D. Vent Diagrams 1. Top Vent - Horizontal Termination One Elbow Two Elbows 1. Top Vent - Horizontal Termination - (continued) Three Elbows V1 = 50 ft. Max. (15.2 m) 2. Top Vent - Vertical Termination Straight up Vertical Venting Three Elbows 2. Top Vent - Horizontal Termination - (continued) Two Elbows 6 A. Pipe Clearances to Combustibles 6 B. Wall Penetration Framing C. Vertical Penetration Framing 7 A. Removing Non-combustible Facing Mate- rial Assembly C. Installing Non-combustible Facing Material B. Securing and Leveling the Appliance D. Installing Flue Restrictors 8 A. Assembly of Vent Sections 8 A B High Temperature Silicone Sealant Page C. Disassembly of Vent Sections B. Securing the Vent Sections D. Installing Heat Shield and Horizontal Termination Cap E. Installing Roof Flashing and Vertical Ter- mination Cap Page 9 A. Fuel Conversions B. Gas Pressures C. Gas Connection 9 Page 10 A. Recommendation for Wire 10 B. Connecting to the Appliance C. Intelli re Ignition System Wiring Note: Appliance will not operate unless properly grounded. D. Junction Box Installation Note TO APPLIANCE INSTALLERS: 11 Heat & Glo Cerona-36, Cerona-42 2106-900 Rev. F 04/08 35 A. Mantel Projections mm 25 51 76 102 127 152 178 203 229 254 279 305 B B. Facing Material C. Finishing Material Options IMPORTANT INSTALLATION Note: D. Hearth Extension 12 12 A. Remove Shipping Materials B. Clean the Appliance C. Accessories Page Page Page STEP 3. A LOG #3 (SRV 2107-703 A STEP 4. LOG #4 (SRV2107-704): STEP 5. LOG #5 (SRV2107-705): STEP 7. LOG #6 (SRV2107-706): 13 A. Before Lighting Appliance 13 CAUTION B. Lighting Appliance CAUTION: NOT FOR USE WITH SOLID FUEL WARNING: DO NOT CONNECT 110 VAC TO THE CONTROL VALVE. IPI Ignition C. After Appliance is Lit D. Frequently Asked Questions 14 14 A. Intelli re Ignition System Sympton Possible Cause Corrective Action Intelli re Ignition System - (continued) Symptom Possible Cause Corrective Action 15 15 A. Maintenance Tasks Inspect Maintenance Tasks 16 16 A. Appliance Dimension Diagram Heat & Glo Cerona-36, Cerona-42 2106-900 Rev. F 04/08 53 B. Vent Components Diagrams Figure 16.2 DVP vent components Page Page Page Page Service Parts List CERONA-36 Service Parts CERONA-36 IPI Valve Assembly Page Service Parts List CERONA-42 Service Parts CERONA-42 IPI Valve Assembly LIMITED LIFETIME WARRANTY HEAT & GLO GAS APPLIANCE PRODUCTS D. Limited Lifetime Warranty