Heath Zenith 3038379, 3038361 specifications Motion Sensing Light Fixture with Accent Lighting

Motion Sensing Light Fixture with Accent Lighting

Models 3038361/3038379

Note: Installation of this light control should be done only by those with experience in 120 Volt household wiring. Some lo- cal codes may require that a licensed electrician install the light control.

This light control automatically turns on lights when motion is detected.

Two lamp holders are provided. The lamp holders are rated at 150 watts max. each.

1. Installation

Caution: Always turn the circuit breaker off when wiring the fixture.

1.Remove the existing fixture.

2.The plastic hanger can be used to hold the fixture while wiring. The small end of the plastic hanger can be threaded through the hole in the center of the cover plate. The small end then goes into one of the slots on the mounting strap.

3.Connect the light control as shown in Figure 1:

•Black sensor wire to the black (HOT) house wire.

•White sensor wire to the white (NEUTRAL) house wire.

Black to black White to white

2. Aiming

The coverage area for the sensor is shown in Figure 2. The sensor should be aimed so that the motion to be detected is in front of and across the coverage area. The sensor should be aimed looking out at a horizontal angle. To reduce false triggering, point the sensor away from traffic areas, air conditioners, dryer vents, water pools, or anything which may move or change temperature rapidly.

240°

8 Ft.

100 Ft.

Figure 2 Coverage Angles

3. Testing

Turn the power back on at the circuit breaker. Turn the light switch on.

From

House

House ground wire to green ground screw on fixture.

Push the rubber plug firmly into place

Note: When first turned on wait about 1 1/2 minutes for the circuitry to calibrate.

Put the TIME switch on the bottom of the sensor in the TEST posi- tion.You can now walk in front of the unit and the lights will come on for about 5 seconds. The TEST mode works both day and night.

Walk through the coverage area and point the sensor to obtain the desired coverage area. Adjust sensitivity as needed. Use Range Boost only if required.

4. Operation

Figure 1 Wiring at Junction Box Plate

4.Attach the fixture to the mounting strap with the center mount- ing bolt. Use a weatherproof sealant to seal the fixture to the junction box.

5.Install the protective lamp shields on the lamp holders by lining up the groves on the narrow end of the shields with the dimples in the lamp holders, push the shields into the lamp holders and turn clockwise slightly.

6.Install the lamps in the lamp holders. Do not over tighten.

7.Adjustment lamp holders. The lamps should be at least 1 inch away from the sensor.

CAUTION: Do not mount the sensor above or touching the lamps (keep 1 inch or more from the lamps). The sensor bottom must be facing down for best coverage and to avoid water damage and electrical shock.

Note: For under-eave installation, rotate the sensor head 180° by bending the sensor towards the clamp bracket. Rotate the sensor bottom clockwise away from the bracket.

For motion sensing, put the ON-TIME switch on the bottom of the sensor in the 1, 5 or 20 minute position. When motion is detected, the lights will come on the selected time. Note: The photocell keeps the lights from turning on in daylight.

To keep lights on all night, flip the light switch off for 1 second then back on. Turning the light switch off for 1 second then back on will return the control to the motion sensing mode. At dawn, the control will return to the motion sensing mode and shut off.

ForAccent Lighting, set the DualBrite® switch to the 3, 6, or Dusk to Dawn setting. The lights will then turn on dim at sundown for the set time. When motion is sensed the lights will turn on full bright.

Specifications:

Total Lighting Wattage.		....................................................300 watts
Lamp Holder Wattage		150 watts max. each
Range	up to 70 ft.; up to 100 ft. with Range Boost
Time Delay		1, 5 or 20 minutes
Accent Lighting Timer		3, 6 hours, Dusk-to-Dawn

Caution: This product is to be used with a U.L. listed rain tight or wet location suitable outlet box. Depending on the installation, additional hardware may be required.

595-5754-03 © 2008