Heath Zenith SL-5655 instruction

Dusk-To-Dawn Patio Light

Model SL-5655

Installation Instructions

READ ALL INSTRUCTIONS CAREFULLY BEFORE BEGINNING INSTALLATION.

NOTE: All wiring must be run in accordance with the National Electrical Code (Canadian Electrical Code in Canada) through conduit or another acceptable means. Contact a qualiﬁed electrician if there is any question as to the suitability of the system.

CAUTION: Make sure the power is off before starting the installation.

This ﬁxture can be mounted on a wall with, or without using a ﬂush-mounted junction box. Do not attempt to mount this ﬁxture on a surface-mounted “Wet Location” junction box. Use the instructions below that apply to your application.

Installation Using A Junction Box

Note: If your junction box protrudes out of the wall slightly, you may want to use the enclosed gasket so less caulking is required.

1.Hold the Mounting Bracket and Gasket over the junction box. Thread the supply wires through the large hole in the back of the Mounting bracket. Select the holes in the mounting bracket that line up with the screw holes in the junction box. Make sure the bottom of the Mounting Bracket is level. Secure with the two #8 screws provided.

Installation Without A Junction Box

1.Select a location on a ﬂat wall with structurally sound wood and from 5 to 25 feet from the ground. The wood should be at least one inch thick to safely secure the ﬁxture.

2.Use the Mounting Bracket as a template. Hold it at the desired mount- ing location (making sure the bottom is level), and mark four mounting holes.

3.Use four #8 or #10 wood screws or galvanized deck screws at least 1 inch long (not provided) to secure the Mounting Bracket to the wall. It may be necessary to drill appropriate pilot holes if mounted to hardwood to avoid splitting.

4.Remove the knockout in the bottom of the Mounting Bracket, and bring your supply wires through this knockout using appropriate ﬂexible conduit or other approved means of wiring.

Complete The Installation

1.Put the Temporary Pin through the holes in the Mounting Bracket.

2.This ﬁxture must be grounded. Connect the supply ground wire to the green ground screw. You can also attach a bare or green “pigtail” to the green ground screw, then connect the ground pigtail to the supply ground when the other supply wires are connected.

3.Slide the ﬁxture onto the Mounting Bracket, and allow the ﬁxture to rest on the Temporary Pin.

4.Connect the ﬁxture wires to the supply wires (black to black, white to white, and if a ground pigtail was added above, connect this pigtail to the supply ground wire). Secure with the wire connectors provided.

5.Remove the Temporary Pin, and slide the ﬁxture all the way down onto the Mounting Bracket making sure no wires get pinched.

6.Install the screw through the bottom of the Mounting Bracket and into the ﬁxture housing. Tighten this screw.

7.Install ONLY a 100 watt mercury vapor type H38 lamp (provided).

8.Caulk ﬁxture mounting surface with silicone weather sealant.

To test operation during daylight, cover the photocontrol with black tape. Turn on the power. The light will take up to ten minutes to reach full bright- ness. Remove the tape from the photocontrol and your unit will operate automatically—on at dusk, off at dawn.

Photocontrol

Fixture	Ground
	Screw

Temporary

Lamp Mounting Bracket

Gasket

(Optional)

598-1059-02

SL-5655 specifications

The Heath Zenith SL-5655 is a state-of-the-art motion-activated LED security light designed to enhance safety and visibility around residential and commercial properties. This innovative product combines superior functionality with energy efficiency, making it a popular choice among homeowners seeking to bolster their outdoor security measures.

One of the standout features of the SL-5655 is its advanced motion detection technology. Equipped with a high-precision passive infrared (PIR) sensor, this light can detect movement within a radius of up to 70 feet. This extended range ensures comprehensive coverage, allowing the light to activate promptly when someone approaches the property. The adjustable sensitivity settings enable users to fine-tune the responsiveness of the sensor, accommodating for varying outdoor conditions and potential false triggering from pets or passing vehicles.

In terms of illumination, the SL-5655 is outfitted with bright, energy-efficient LED bulbs that deliver 1800 lumens of light output. This powerful brightness not only provides substantial illumination to deter intruders but also enhances visibility for activities such as entering and exiting a property after dark. The LED technology also promises an impressive lifespan, significantly reducing the need for frequent bulb replacements, and contributing to lower maintenance costs over time.

Another significant characteristic of the Heath Zenith SL-5655 is its versatility in installation. The light can be mounted on walls, sidings, or even eaves, making it suitable for various types of properties. Additionally, its sleek and modern design ensures that it blends seamlessly with most outdoor decors.

The device also features an adjustable time setting that allows users to control how long the light stays on once activated. This feature is particularly useful for homeowners who wish to set the light to remain on for a specific duration, such as while walking to and from their vehicles or entering their homes after dark.

Furthermore, the SL-5655 is designed to withstand various weather conditions, ensuring reliable operation in rain, snow, and heat. Its durable exterior enhances longevity and performance in outdoor settings.

Overall, the Heath Zenith SL-5655 is an excellent choice for customers looking for a reliable, motion-activated security light that smartly combines advanced technology with practical features and energy efficiency, providing peace of mind for any property.

Heath Zenith SL-5655 installation instructions Installation Instructions

Models: SL-5655