T4800 INSTALLATION INSTRUCTIONS

15. Completion of the Enclosure

Complete the fireplace enclosure, allowing space for outside air ducts and gas piping if desired. Electrical wiring should not come in contact with the fireplace.

A minimum clearance of 1½” must be maintained between the fireplace sides and the enclosure as well as the fireplace back and the enclosure. See pages 9-10 for framing details.

NOTE: Use only a noncombustible material to fin- ish the face of the fireplace below the level of the front standoffs. A noncombustible material such as USG MICORE CV230 Mineral Fiber Board, or USG DUROCK Cement Board is recommended for this purpose.

CAUTION:

When using a gas log set, the fireplace damper must be set in the fully open position. This en- sures proper venting of combustion products.

16.Gas Log/Lighter Provisions

Knockouts are provided on both sides of the fireplace to allow for connection of a certified gas log lighter or a decorative gas appliance with a maximum input of 100,000 BTU/hour, incorporating an automatic gas shut-off device and complying with the Standard for

Decorative Gas Appliances for Installation in Vented Fireplaces, ANSI Z21.60. The decorative gas appliance should be installed in accordance with the National Fuel Gas Code, ANSI Z223.1-1980. The side refractories are designed to allow ½” iron pipe to pass through. Use a noncombustible sealant to seal any opening between the gas pipe and refractory on the inside. Repack the insulation removed to seal around the gas pipe where it exits the side of the fireplace. A minimum 1½” air clearance must be provided around the ½” iron pipe for a minimum of 4 inches beyond the fireplace. See Figure 16.

Figure 16 - Air Clearance Around Gas Line

CLEARANCES!

A minimum 1½” air clearance must be maintained at the back and sides of the fireplace assembly except at the nailing flange where the clearance is ½”.

Chimney sections at any level require a 2” minimum air space clearance between the framing and chimney section.

WARNING!

This fireplace was not tested by the fireplace manufacturer for use with an unvented gas log heater. To reduce risk of injury, do not install an unvented gas log heater in this fireplace unless it has been specifically tested and listed by Underwriter’s Laboratories Inc. for use in this specific model fireplace. Unless the unvented gas log heater is tested and listed for use in this factory-built fireplace, a fire hazard may be cre- ated that can result in a structure fire.

12-01

17

34922 Rev B

Page 16 Page 18
Page 17
Image 17
Heatiator T4800 manual Completion of the Enclosure, Gas Log/Lighter Provisions
Page 16 Page 18

T4800 specifications

The Heatiator T4800 is an advanced heating solution designed to deliver exceptional performance and efficiency for residential and commercial spaces. This state-of-the-art heater combines innovative technologies with user-friendly features to ensure a comfortable atmosphere, regardless of the external weather conditions.

One of the standout features of the Heatiator T4800 is its powerful heating capacity. It can rapidly warm up large areas, making it ideal for open-plan living spaces and office environments. The unit employs a highly efficient heating element that ensures an even distribution of warmth, eliminating cold spots and enhancing overall comfort.

In terms of technology, the Heatiator T4800 integrates smart thermostatic controls. Users can easily set their desired temperature through a digital interface, allowing for precise adjustments. Additionally, the heater offers a programmable timer that lets users schedule heating cycles based on their routines, ensuring energy is not wasted when spaces are unoccupied.

Safety is paramount in the design of the T4800. It comes equipped with advanced features such as overheat protection and tip-over switches, which automatically cut off power to the unit if it becomes too hot or is inadvertently knocked over. This provides peace of mind, especially in households with children or pets.

Energy efficiency is another hallmark of the Heatiator T4800. The heater boasts a high Energy Efficiency Ratio (EER), which translates to significant savings on energy bills. Its environmentally friendly heating technology minimizes carbon emissions, making it a sustainable choice for environmentally conscious consumers.

The sleek and modern design of the Heatiator T4800 allows it to blend seamlessly with any décor. With a compact form factor, it can be placed nearly anywhere without taking up valuable space. Its whisper-quiet operation means it won’t disrupt daily activities or sleep, making it suitable for bedrooms, living rooms, and offices alike.

Moreover, the Heatiator T4800 is designed for easy maintenance. The accessible filter can be cleaned or replaced with minimal effort, ensuring optimal performance and longevity.

Overall, the Heatiator T4800 stands out in the crowded market of heating devices. Its combination of advanced features, efficiency, safety, and modern design makes it an outstanding choice for anyone looking to improve their indoor comfort.
Top Page Image Contents