Hifionics manual Colossus Dual Mono Block Amplifier Applications, Basic Application

COLOSSUS DUAL MONO BLOCK AMPLIFIER APPLICATIONS

BASIC APPLICATION

The Colossus Dual Mono Block amplifiers are capable of 4, 2 & 1 Ohm stereo and 4 & 2 bridged loads.

SINGLE AMP INSTALLATION PROCEDURE:

1.Connect the amp LINE INPUTS to the Radio/CD player full range or mono line out puts with good quality RCA interconnect cables.

2.Plug in the HFR-G1 bass remote module into the amp REMOTE INPUT jack.

3.Route a 0 gauge power cable directly to the vehicle battery with an in-line 300 amp fuse.

This will allow you to operate separate subs independently (on each channel L or R) at 4, 2 or 1 Ohm at up to 1600 watts or bridged across L & R to operate a single sub up to 3200 watts at 4 or 2 Ohms.

Note: The amp is not capable of 1 Ohm when bridged across L & R.

The crossovers and HFR-G1 Remote Module will operate both L & R channels simultaneously.

4.Connect a 0 gauge ground cable directly to chassis ground with in 36” of the amp.

-Be sure to remove any paint or primer from the ground point.

-Use a nut, bolt and lock washer to secure the ground cable to the chassis ground.

5.Connect the subwoofer(s) in accordance to the diagrams below.

USING CHANNELS L & R INDEPENDENTLY

FULL RANGE

STEREO LINE INPUTY-ADAPTOR

NOT USED

	R	L
		INPUT
DESIGNATED MONO	R	OUTPUT
		L
LINE INPUT		BALANCED INPUT

Note: You can use the Radio/CD designated mono line output or a full range stereo line output.

For full range stereo line output, you will need an optional “Y-Adaptor” as shown

Note: The amplifier is capable of 4, 2 & 1 Ohms per channel in this configuration

-
R-CH	BRIDGED
+

	-6dB	HFR-G1
		DIAGNOSTICS	CLIP
		GREEN: POWER	GREEN: PRE-CLIP
		AMBER: THERMAL	AMBER: SOFT CLIP
-20dB	0dB	RED: SHORT	RED: HARD CLIP

REMOTE LEVEL

9V 0.2V	LEVEL
0 180	PHASE
0 10dB	BOOST
PARAMETRIC EQ	BANDWIDTH
30 100Hz	FREQ
15 35Hz	REMOTE	HFR-G1
	SONIC	SUB
35	LPF
250Hz

-

L-CH

+

REM

REMOTE TURN-ON

GND	CHASSIS GROUND
POWER
	TO BATTERY +12v VIA
+12V
	300 AMP FUSE

RED - CLIP AMBER - NEAR CLIP GREEN - PRE-CLIP DIAGNOSTICS RED - SHORT CIRCUIT AMBER - THERMAL

USING CHANNELS L & R BRIDGED

FULL RANGE
STEREO LINE INPUT	Y-ADAPTOR

NOT USED

Note: You can use the Radio/CD designated mono line output or a full range stereo line output.

For full range stereo line output, you will need an optional “Y-Adaptor” as shown

Note: The amplifier is capable of 4 & 2 Ohms in this configuration. It is not capable of 1 Ohm.

BRIDGED MONO

SUBWOOFER

2 OHM MINIMUM

DESIGNATED MONO

LINE INPUT

	-6dB	HFR-G1
		DIAGNOSTICS	CLIP
		GREEN: POWER	GREEN: PRE-CLIP
		AMBER: THERMAL	AMBER: SOFT CLIP
-20dB	0dB	RED: SHORT	RED: HARD CLIP

REMOTE LEVEL

R	L
		INPUT
R	L	OUTPUT
		INPUT	BALANCED
9V 0.2V		LEVEL
0 180		PHASE
0 10dB		BOOST
PARAMETRIC EQ		BANDWIDTH
30 100Hz		FREQ
15 35Hz		REMOTE	HFR-G1
		SONIC	SUB
35		LPF
250Hz
AMBER - NEAR CLIP GREEN - PRE-CLIP	RED - CLIP	DIAGNOSTICS RED - SHORT CIRCUIT AMBER - THERMAL

-
R-CH	BRIDGED
+
-
L-CH
+
REM

REMOTE TURN-ON

GND	CHASSIS GROUND
POWER
	TO BATTERY +12v VIA
+12V
	300 AMP FUSE

3