Hitachi CMP4202 Anti-tumble measures

Anti-tumble measures

Securing to a wall or pillar

Using a commercially available cord,

chain and clamp, secure the set to a firm

wall or pillar.

Securing desktop

1)Using wood screws (two), fasten the set to the

clamping screw holes on the rear of the stand

as shown.

2)Using commercially available wood screws,

secure the set firmly in position.

No stand is provided with this product. When installing the monitor,

use the optional Desk-top Stand (CMPAD05), Wall Mount Unit

(horizontal-mount CMPAK05, vertical/horizontal-mount CMPAK15),

or Ceiling Mount Unit (CMPAT05).

The Desk-top Stand has been used for the illustrations in this

manual.

Using the optional vertical-mount unit

(CMPAK15)

Using the optional wall-mount unit (CMPAK15) allows set to mount

on wall surfaces as shown at below.

1) Make at least four sets of commercial anchor bolts and screws

available to meet various kinds of walls to mount on.

2) Read the instructions supplied with the wall-mount unit carefully to

optimally locate the plasma display on a wall surface.

3) Prepare the wall surface for anchoring and drilling as needed, as

shown in the sketches.

• Make sure that an adequate wall surface strength and a screw

holding strength are available.

SPEAKER

TERMINAL

8 8W

SPEAKER

TERMINAL

8 8W

Contents

Main USER'S MANUAL Notes on lnstallation Work: Note for Dealers: CMP4201 CMP4202 FEATURES CONTENTS Page WARNING CAUTION Do not coil or wind the power cord. Caution for 200 - 240V operation only INFORMATIVE EXAMPLES OF PROTECTIVE DEVICES IN SINGLE - PHASE EQUIPMENT OR SUB - ASSEMBLIES PRECAUTIONS Installation environment How to view the monitor. Note on image retention PRECAUTIONS(continued) How to clean the monitor. Prevention of an obstacle to Radio receivers Precautions for the monitor Precaution during transportation This product is complete with the display monitor, plus the accessories shown below. Component Names Front External device connection terminals Control panel Rear Remote controller Component Names (continued) Handling the Remote Controller Loading Batteries CAUTIONS Anti-tumble measures Securing to a wall or pillar Securing desktop Using the optional vertical-mount unit (CMPAK15) Connecting to a PC Choose an appropriate site and install the product on a level table where the stand is secure. PC INSTALLATION INSTRUCTIONS (continued) Monitor rear panel Connecting to a Video Imaging Device (When the optional video unit is installed.) INSTALLATION INSTRUCTIONS (continued) With RGB component setup Monitor rear panel External Monitor Page OPERATING INSTRUCTIONS Turning Power On and Off Indicating lamp Audio Mute Input Switching Volume Adjustment VOLUME 15 Size Switching >> << Displaying Two Screens Input Signal Screen Display Using the Menu Screen (On-screen display system) Independent Operation of Multiple Monitors (ID No) Automatic Adjustment of Screen Position and the Clock CAUTIONS PICTURE MENU NORMAL LIFE EXTEN.1 LIFE EXTEN.2 COLOR TEMP. ENHANCER OPERATE MODE PICTURE MENU (continued) SOUND MENU AUTO ADJUST* V.POSITION * DISPLAY MENU (This function can only be used when the optional video unit has been inserted.) This function can only be used when the optional video unit has been inserted. DISPLAY MENU (continued) Display area selection diagram (RGB input) Display size selection diagram TIPS FUNCTION MENU DISPLAY MENU (continued) VIDEO 2 RGB1 SIGNAL (RGB2 SIGNAL RGB VIDEO OTHER MENU AUTO DISPLAY WHITE OFF ON 60MIN ID NO. OTHER FEATURES Automatic Store Changes in the signal status are displayed on the screen as they arise. Signal Check Status Display Action Menu Display Registration condition OTHERFEATURES (continued) Power Save Mode NOTES IMAGE RETENTION OF PLASMA DISPLAY Symptoms That Seemingly Appear to be Failures TROUBLESHOOTING Customer servicing can be hazardous. WARNING TROUBLESHOOTING (continued) Symptoms That Seemingly Appear to be Failures (continued) Actions to Correct Abnormal Displays B TROUBLESHOOTING (continued) Product specifications and designs are subject to change without notice. PRODUCT SPECIFICATIONS Signal Input RGB terminal (D-sub 15-pin connector) Sync signal type Priority Pin Input signal Recommended Signal List Signal Input (continued) PRODUCT SPECIFICATIONS (continued) S-input connector pin specifications Recommended Signal List (continued) With Composite/S-video Input(VIDEO1 input). With component input (VIDEO2 input) PRODUCT SPECIFICATIONS (continued) With R, G, B Video input (VIDEO1 and VIDEO2 input).