P L E A S E R E A D A N D S AV E T H E S E
I M P O R TA N T S A F E T Y I N S T R U C T I O N S
F E AT U R E S - O p e r at i o n s
C L E A N I N G / S T O R A G E
When using electrical appliances, basic safety precautions should always be taken including the following:
1.Read all instructions before using this appliance.
2.Use fan only for purposes described in the instruction manual.
3.To protect against electrical shock do not immerse unit, plug or cord in water or spray with liquids and plug the appliance directly into a 120V AC electrical outlet.
4.Close supervision is necessary when any appliance is used by or near children.
5.Unplug from outlet when not in use, when moving fan from one location to another, before putting on or taking off parts and before cleaning.
6.Avoid contact with moving parts.
7.Do not operate in the presence of explosive and/or flammable fumes.
8.To avoid fire hazard, NEVER place the cord under rugs or any parts near an open flame, cooking or other heating appliance.
9.Do not operate any appliance with a damaged cord or plug after the appliance malfunctions, or has been dropped/damaged in any manner. Discard fan or return to an authorized service facility for examination and/or repair.
10.Do not run cord under carpeting. Do not cover cord with throw rugs, runner, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.
11.The use of attachments not recommended or sold by the appliance manufacturer may cause hazards.
12.Do not let the cord hang over the edge of a table, counter or come in contact with hot surfaces or leave exposed to high traffic areas.
13.Do not use outdoors.
14.To disconnect, grip plug and pull from wall outlet. Never yank on cord.
15.Always use on a dry, level surface.
16.Do not operate fan until fully assembled with all parts properly in place.
17.This product is intended for household use ONLY and not for commercial or industrial applications.
18.WARNING: To reduce the risk of electrical shock and injury to persons, do not use in window.
19.WARNING: To reduce the risk of fire or electric shock, do not use this fan with any
20.This product employs overload protection (fuse). A blown fuse indicates an overload or
PLEASE READ AND SAVE THESE IMPORTANT safety instructions
PRE-OPERATING INSTRUCTIONS
THIS PRODUCT COMES FULLY ASSEMBLED AND IS READY FOR IMMEDIATE USE.
OPERATING INSTRUCTIONS
1.Clip fan onto a dry, level surface.
2.Please make sure the power switch located on the back of the motor housing is in the "Off" position. Plug the cord into any standard
3.The SPEED is adjusted by moving the switch located on the motor housing left or right to the desired setting.
4.The OSCILLATION control knob is located on the top of the fan motor housing. To start oscillation, push the control knob down. To stop oscillation, pull the control knob up.
Figure 1 |
|
|
|
| J |
A |
| I |
B |
| H |
|
| |
K | G | F |
| ||
|
| E |
|
| D |
Wall mounting INSTRUCTIONS
NOTE: On the underside of the fanʼs clip there are “KEY SLOTS” (2).
Select a suitable spot on a wall (away from curtains, draperies, or heat sources) where you want to mount the fan. Use a No. 10 pan head wood screw (1 1/4” length) and thread into a 2x4 wood stud behind the dry wall. Please refer to the warning below if you are unable to locate a wood stud in the wall.
When threading the screw into the wall, leave approximately 1/4” clearance between the screw and wall. This will allow the clipʼs “KEY SLOTS” to fit easily and securely over the screws. If necessary, the screw may be tightened further to ensure the fan is firmly attached to the wall.
WARNING: WHEN MOUNTING THE FAN TO PLASTER, DRYWALL OR SHEETROCK, YOU MUST USE A MOLLY BOLT, OR SIMILAR FASTENER. DOING SO WILL PREVENT THE FAN FROM BECOMING DISLODGED WHILE IN OPERATION.
ADJUSTMENT INSTRUCTIONS
Vertical Angle Adjustment
1.To change the tilting angle of the fan head, simply loosen the tilt adjustment knob.
2.Move the fan head to the desired angle, then firmly tighten the knob to lock the fan head in place.
Horizontal Angle Adjustment
Turn the motor housing to the desired direction.
WARNING: MAKE SURE TO SUPPORT THE FAN HEAD ASSEMBLY WHEN LOOSENING THE ADJUSTABLE HEIGHT NUT, AS THE WEIGHT OF THE FAN HEAD MAY CAUSE THE
cleaning/maintenance
Follow these instructions to correctly and safely care for your oscillating clip fan. Please remember:
Replaceable Fuse
If your (5 Amp, 125 Volt) replaceable fuse blows, please order a new fuse at
User Servicing Instructions
1. | Unplug your fan. Grasp plug and remove from the | |
| receptacle or other outlet device. Do not unplug by | |
2. | pulling on cord. |
|
Open fuse cover, located on the top of the plug, by | ||
| using your thumb or a flathead screwdriver to slide | |
| the cover down towards the prongs. | |
| Note: Ensure that fuse cover is completely open | |
3. | before attempting to remove fuse. | |
Remove fuse carefully by | Figure 2 | |
| using a small screwdriver | |
| to pry the fuse out of the | Fuse coverFuse |
| compartment by the metal | |
| ends of the fuse (see |
|
4. | FIGURE 2). |
|
Place plug on a solid, flat |
| |
| surface. Insert new 5 | Metal ends |
| Amp, 125 Volt fuse into |
|
| fuse compartment and use a small screwdriver to | |
| secure the metal ends of the fuse into the | |
| compartment. |
|
| Caution: Risk of fire. Replace fuse only with 5 | |
5. | Amp, 125 Volt fuse. |
|
Slide fuse cover closed completely. If fuse cover is | ||
| difficult to close, make sure fuse is secured in place | |
Fan Cleaning
• Always unplug the fan before cleaning or disassembling.
• Do not allow water to drip on or into the fan motor housing.
• Do not use any of the following as a cleaner: gasoline, thinner, benzene.
1. To access the fan blade, remove the front grill by pressing the tabs on the grill ring away from the fan.
2. Clean the fan blade, both front and rear grills with a soft cloth moistened with a mild soap solution.
NOTE: FAN BLADE SHOULD NOT BE REMOVED.
3. Replace the front grill by snapping back into rear grill.
Using a soft, moist cloth, with or without a mild soap solution, carefully clean the fan head. Please use caution around the motor housing area. Do not allow the motor or other electrical components to be exposed to water.
FAN STORAGE
In the
•IMPORTANT: Keep your fan in a safe dry location, where the fan is not likely to fall or be crushed.
•Your fan should be stored fully assembled.
•Remember to protect the fan head from dust or moisture.
If you have any questions regarding your product or would like to learn more about other Holmes® products, please contact our Consumer Service
This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet.
Do not attempt to modify this plug or defeat this
safety feature in any way.
| C |
|
|
A. | Front Grill | G. | Pivot Bracket |
B. | Fan Blade | H. | Motor Housing |
C. | Key Slots (underside | I. | Oscillation Knob |
D. | of clip) | J. | Rear Grill |
Pivot Caps (2) | K. | Tilt Adjustment Knob | |
E. | Clip |
|
|
F. | Clamp Pivot |
|
|
EXTENSION POLE TO COLLAPSE.
It is suggested that you refer to a local hardware retailer in case you need additional information on mounting your fan to a wall.
completely by pressing down on metal ends of the |
fuse. |
6. Risk of fire. Do not replace attachment plug. |
Contains a safety device (fuse) that should not be |
removed. Discard product if the attachment plug is |
damaged. |
Department at
HACP10_11EM1.indd 2
7/18/11 3:57 PM 
