HASF1406_07EM1.qxd 9/29/07 10:38 Page 2
P L E A S E R E A D A N D S AV E T H E S E
I M P O R TA N T S A F E T Y I N S T R U C T I O N S
F E AT U R E S - O P E R AT I O N S
F E AT U R E S - O P E R AT I O N S C L E A N I N G / M A I N T E N A N C E
When using electrical appliances, basic safety precautions should always be taken including the following:
1. | Read all instructions before using this appliance. |
2. | Use fan only for purposes described in the instruction |
| manual. |
3. | To protect against electrical shock do not immerse unit, |
| plug or cord in water or spray with liquids and plug |
| the appliance directly into a 120V AC electrical outlet. |
4. | Close supervision is necessary when any appliance is |
| used by or near children. |
5. | Unplug from outlet when not in use, when moving |
17.WARNING: To reduce the risk of electrical shock and injury to persons, do not use in window.
18.WARNING: To reduce the risk of fire or electric shock, DO NOT use this fan with any
PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS
| Figure 1 |
| Q | P | O | N | M |
|
S | R |
|
|
| L | ||
T |
|
|
|
|
| ||
|
|
|
|
|
| K | |
|
|
|
|
|
|
| |
|
|
|
|
|
|
| J |
|
|
|
|
| H |
| I |
|
|
|
|
|
|
| |
|
|
|
| G |
|
| F |
Figure 3 | D |
|
E
C
B
A
6.Secure the Front Grill (T) to the Rear Grill of the fan by positioning the hanging clip of the Front Grill over the Rear Grill. Close the remaining four Grill Clips (N) of the Front Grill over the Rear Grill. Refer to Figure 8.
ADJUSTMENT INSTRUCTIONS
Fan Head Tilt Adjustment
Loosen
CLEANING/MAINTENANCE INSTRUCTIONS
Follow these instructions to correctly and safely care for your fan.
• Always unplug the fan before cleaning or disassembling. |
• Be sure to clean your fan with a soft cloth moistened |
with a mild soap solution. |
• Do not allow water to drip on or enter into the fan |
motor housing. |
• Do not use gasoline, thinner, or benzene as a cleaner. |
• Lightly run a vacuum cleaner nozzle over the fan grill |
to remove any dust or dirt that may have accumulated. |
| fan from one location to another, before putting on |
| or taking off parts and before cleaning. |
6. | Avoid contact with moving parts. |
7. | Do not operate in the presence of explosive and/or |
| flammable fumes. |
8. | To avoid fire hazard, NEVER place the cord under |
| rugs or any parts near an open flame, cooking or |
| other heating appliance. |
9. | Do not operate any appliance with a damaged cord |
| or plug after the appliance malfunctions, or has been |
| dropped/damaged in any manner. |
10. | The use of attachments not recommended or sold by |
| the appliance manufacturer may cause hazards. |
11. | Do not let the cord hang over the edge of a table, |
| counter or come in contact with hot surfaces or leave |
| exposed to high traffic areas. |
12. | Do not use outdoors. |
13. | To disconnect, grip plug and pull from wall outlet. |
| Never yank on cord. |
ASSEMBLY INSTRUCTIONS
Tools required: One Phillips head screw driver
Assembly time:
1. | Secure the Base Weight (C), Base (D), and Long |
| Extension Pole (E) together using the |
| (A) and Washer (B). Refer to Figure 3 for the correct |
| alignment of the Long Extension Pole to the Base. |
2. | Align the holes of the Long Extension Pole (E) and |
| Short Extension Pole (G) together and secure with |
| Phillips head screw (F) and tighten with screw driver. |
| Refer to Figure 4. |
3. | Align the holes of the neck of the Short Extension Pole and |
| the Neck (H) together and secure with the Phillips head |
| screw (F) and tighten with screw driver. Refer to Figure 5. |
4. | Secure the Rear Grill (O) to the Motor Housing (K) by |
| tightening the Rear Grill Nut (P). Refer to Figure 6 |
A.(1)
B.(1) Washer
C.Weight
D.Base
E.Long Extension Pole
F.(2) Phillips head screws
G.Short Extension Pole
H.Neck
I.Tilt Adjustment Knob
J.Fan Speed Pull Chain
K.Motor Housing
L.Oscillation Knob
M.Motor Shaft
N.Grill Clips
O.Rear Grill
P.Rear Grill Nut
Q.(1) Blade screw
E
D
C
B 
A 
R.Blade
S.Hanging Clip
T.Front Grill
Figure 4 | G |
|
F 
E
Figure 5
H
OPERATING INSTRUCTIONS
Fan Speed Pull Chain (J)
1st = High ( III ) 2nd = Medium ( II ) 3rd = Low ( I )
4th = Off (o)
Oscillation Knob (L) ( 
) Push, Pull = Oscillation On, Off
Figure 7 |
FAN BLADE CLEANING
Make sure the fan is unplugged before disassembling and cleaning the fan blade. Unclip and remove the front grill. Wipe the blade with a soft cloth moistened with a mild soap solution. DO NOT allow any liquid to drip into or enter the Motor Housing.
FAN STORAGE INSTRUCTIONS
Your fan should be stored in the
•We recommend using the original (or appropriately sized) box.
•Please remember to protect the fan from dust or moisture.
14. | Always use on a dry, level surface. |
15. | Do not operate fan until fully assembled with all |
| parts properly in place. |
16. | This product is intended for household use ONLY and |
| not for commercial or industrial applications. |
for correct positioning of the Rear Grill to the Motor |
Housing. |
5. Secure the Fan Blade (R) to the Motor Shaft (M) by |
tightening the Blade Screw (Q) with a screw driver. |
Refer to Figure 7 for the correct alignment of the Fan |
Blade to the Blade Shaft. |
Figure 2 |
A (X 1) |
Q (X 1), F (X 2) |
F
G
Figure 6
3 pt |
Figure 8
S
If you have any questions regarding your product or would like to learn more about other Holmes® products, please contact our Consumer Service Department at
THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS
SAFETY FEATURE IN ANY WAY.
B (X 1) |
O 
P 
