PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:
1) | Read all instructions before using the appliance. |
2) | To avoid fire or shock hazard, plug the appliance |
| directly into a 120V AC electrical outlet. |
3) | Keep the cord out of heavy traffic areas. DO NOT let |
| the cord hang over the edge of a table or counter. |
| To avoid fire hazard, NEVER put the cord under rugs, |
10) | Use appliance only for intended household use as |
| described in this manual. Any other use not |
| recommended by the manufacturer may cause fire, |
| electric shock, or injury to persons. The use of |
| attachments not recommended or sold by The |
| Holmes Group may cause hazards. |
11) | DO NOT use outdoors. |
12) | Always use on a dry, level surface. |
13) | Keep unit away from heated surfaces and open |
| flames. |
14) | WARNING: To reduce the risk of fire or electric shock, |
| DO NOT use this fan with any |
| device. |
15) | DO NOT attempt to repair or adjust any electrical or |
| mechanical functions on this unit. Doing so will |
| void your warranty. The inside of the unit contains |
Figure 1
B
AC
A. LOGO PLATE (SNAP ON) |
B. FRONT GRILL |
C. BLADE CAP |
D. FAN BLADE |
E. REAR GRILL |
MOUNTING RING |
F. PLASTIC BAND |
G. GRILL SCREW |
H. REAR GRILL |
D | H | J | K | |
E | I | |||
L | ||||
| ||||
|
|
| M | |
|
|
| N | |
|
|
| O | |
F | G |
|
| |
|
|
| ||
|
|
| P | |
M. MOTOR HOUSING |
|
|
| |
N. TILT JOINT |
|
| Q |
O.TILT ADJUSTMENT KNOB
P.FAN POST SCREW
Q. EXTENSION POLE | R |
| |
R. BASE COLLAR | S |
S. BASE | T |
| |
T. FOOT EXTENSIONS (4) |
|
Pole Assembly:
You will need the completed base and extension pole.
STEP 1: Remove the base collar from the base by turning counterclockwise.
STEP 2: Take the extension pole, with the solid end down, and insert it into the base. The hollow end of the pole (with the screw hole) will be facing up.
STEP 3: PReplace the base collar over the extension pole, slide it down the pole, and secure it to the base by turning clockwise.
Figure 3
Step 3: Slide the fan blade, with the hollowed interior of the blade facing towards the rear grill firmly onto the motor shaft. Make sure the shaft protrudes from the front of the blade.
Step 4: Secure fan blade onto the motor shaft by turning the blade cap in a
Step 5: Prepare the front grill by simply snapping the circular front grill logo plate in place.
Step 6: Center the front grill by aligning the Holmes logo so it is horizontal and parallel to the floor. Then secure the front and rear grills completely together by snapping into place. Lastly, tighten the grill screw at the bottom of the rear grill.
OPERATING INSTRUCTIONS:
STEP 1: Set fan on a dry, level surface.
STEP 2: Plug cord into any standard 120V AC outlet. Please make sure the selector (speed) control is in the OFF position. Selector (speed) control is located on the top of the fan motor housing.
STEP 3: The SPEED is adjusted by turning the control knob to the desired setting,
STEP 4: The OSCILLATION control knob is located on the top of the fan motor housing. To start oscillation, push control knob down. To stop oscillation, pull control knob up.
| near heat registers, radiator, stoves, or heaters. |
4) | To protect against electrical hazards, DO NOT immerse |
| in water or other liquids. Do not use near water. |
5) | Close supervision is necessary when any appliance is |
| used by or near children, or by disabled people. |
6) | Always unplug the fan before moving it, putting on or |
no user serviceable parts. All servicing should be |
performed by qualified personnel only. |
PLEASE READ AND SAVE
I. | MOTOR SHAFT |
J. | GILL MOUNT |
K. | SPEED CONTROL KNOB |
L. | OSCILLATION KNOB |
Extension
Pole
Base
Collar
Final Assembly:
First, place fan head assembly onto the extension pole, lining up the fan post screw with the hole in the extension pole. Then, simply insert the fan post screw into the hole and tighten until a secure fit is obtained. Lastly, insert the tilt adjustment knob into the neck joint and tighten in place.
ADJUSTMENT INSTRUCTIONS:
taking off parts, cleaning, or whenever the fan is not |
in use. Be sure to pull by the plug and not the cord. |
7) Avoid contact with moving parts. DO NOT operate |
without fan grills properly in place. |
THESE IMPORTANT
SAFETY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS:
Base Assembly:
You will need the base and four extension legs.
Push in the small tab on each extension and snap into base.
Base
NOTE: If your fan does not have a screw hole in the extension pole but instead has an indentation around the top of the pole; please do the following:
Tilt Adjustment:
Follow these instructions to tilt the Fan Head for upward angle air movement.
8) | DO NOT operate any appliance with a damaged cord |
| or plug, if motor fan fails to rotate, after the appliance |
| malfunctions, or if it has been dropped or damaged in |
| any manner. Return appliance to manufacturer for |
| examination, electrical or mechanical adjustment, or |
| repair. |
9) | DO NOT operate in the presence of explosive and/or |
| flammable fumes. |
|
|
THIS PRODUCT IS EQUIPPED WITH A POLARIZED AC (Alternating Current) PLUG (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact qualified personnel to install the proper outlet.
DO NOT DEFEAT THE SAFETY PURPOSE OF THIS
POLARIZED PLUG IN ANY WAY
Figure 2
Fan Head Assembly:
You are now ready to assemble the fan head (See Figure #1)
Step 1: Position the rear grill over the motor shaft, making certain the 2 notches at the top and bottom of the rear grill fit over the 2 prongs on the motor hous- ing. Please make sure the rear grill fits securely against the motor housing.
Step 2: Secure the rear grill in its place using the rear grill mounting nut. Turn this nut clockwise and tighten firmly.
Step 1: First, place the fan head assembly onto the extension pole and tighten the fan post screw until a secure fit is obtained.
Step 2: Insert the tilt adjustment knob into the neck joint and tighten in place.
Figure 4
Fan Post Screw
Screw Hole
Extension Pole
Step 1: To change the tilting angle of the fan head, simply loosen the Tilt Adjustment Knob (see fig.1).
Step 2: Move the fan head to the desired angle, then firmly tighten the knob to lock in place.
Height Adjustment:
Follow these instructions to adjust the height of the fan.
Step 1: Turn the extension pole base collar (see figure 3)
Step 2: Adjust the pole to the desired height, and firmly tighten collar in a clockwise direction.
