ACCUTEMP™ DIGITAL THERMOSTAT
Your heater is equipped with an AccuTemp™ Digital Thermostat that allows you to set your heater to your precise comfort level.
Setting the AccuTemp™ thermostat:
1.Make sure the Manual/AccuTemp™ switch is set to AccuTemp™. The LCD display will read 75°.
2.Turn the mode control to LO(Low) or HI(High).
3.Push the temperature set button until the display reads your desired temperature.
To increase the temperature push the top button, for lower tempera- tures push the lower button. When finished setting the temperature, release the button and the display will flash to indicate the thermo- stat will be set to that temperature.
4.The display will return to existing room temperature and gradually increase until the room has reached your
5.If the unit will not start in the AccuTemp™ mode, please make sure the “set temperature” is higher than the current room temperature.
NOTE: It is normal for the heater to cycle ON and OFF as it maintains the preset temperature. To prevent the unit from cycling, you need to raise the thermostat setting. When the preset temperature is made, the fan will run for 30 seconds without heat. This cool down process ensures an accurate and consistent temperature reading. If you unplug the heater, you will have to reset the AccuTemp™ thermostat again by following the above instructions.
Manual Operation:
1.If you want the heater to run continuously, turn the Manual/AccuTemp™ switch to Manual and adjust the mode control to LO(Low) or HI(High).
SETTING THE THERMOSTAT
1.You need to set thermostat on HI(High) to start heater (See fig.#1 and #2). Allow heater to operate and warm up the room.
2.When the desired temperature/comfort level is reached, lower the thermostat setting until the fan/heater stops operating.
3.The control will now automatically maintain the
Note: It is normal for the heater to cycle ON and OFF as it maintains the preset temperature. To prevent the unit from cycling, you need to raise the thermostat setting.
Figure 2 |
| ACCUTEMP™ | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
MODE CONTROL |
| THERMOSTAT |
HEAT CONTROLS | TEMPERATURE | |
OFF | LOW 1000W | RANGE DISPLAY |
FAN | HI 1500W |
|
CLEANING/MAINTENANCE
During Season Care:
Always unplug the heater, before moving or cleaning.
1.Carefully wipe the unit with a soft, damp cloth. Please be very cau- tious near the motor and heating elements.
2.After cleaning, be sure to completely dry the unit with a cloth or towel.
After Season Care:
1.Store heater in a cool, dry location.
2.Holmes® recommends that you store the unit in its original carton.
TROUBLESHOOTING
If your heater fails to operate:
•Make sure the electrical outlet or circuit breaker is working.
•Check for obstructions. If you find an obstruction turn the heater OFF, and unplug the unit. Carefully remove the obstruction and follow the reset instructions.
•The thermostat might be set too low. Adjust the thermostat until the heater restarts.
•Make sure selector is in LO(LOW) or HI(HIGH) setting.
If your heater fails to oscillate:
• Make sure the oscillation switch is in the
Please DO NOT attempt to open or repair the heater. Please see the Warranty for Service Instructions.
Figure 1 |
|
| A. ACCUTEMP™ | |
| B | I | C D | THERMOSTAT |
A | B. ACCUTEMP™ | |||
|
| E | DIGITAL LCD | |
|
|
|
| DISPLAY |
|
|
| J | C. POWER LIGHT/ |
|
|
| F | MODE |
|
|
| D. MODE CONTROL | |
E. CARRY GRIP
F. AIR FILTER
G. REAR GRILL PANEL
H. OSCILLATION BASE
I. MANUAL/
ACCUTEMP SWITCH
J. OSCILLATION
SWITCH
G
H
