Holmes HFH2986 PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS, PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS FEATURES - OPERATIONS, FEATURES

18. DO NOT attempt to repair or adjust any electrical or

mechanical functions on this unit. Doing so will void

your warranty. The inside of the unit contains no user

serviceable parts. All servicing should be performed by

qualified personnel only.

19. Discontinue use if plug or outlet is hot. It is recommended

that the outlet be replaced if plug or outlet is hot to touch.

PLEASE READ AND SAVETHESE IMPORTANTSAFETY INSTRUCTIONS

TECHNICAL SPECIFICATIONS

• Wattage: 1500W (+5% -15%)

• Working voltage: 120V AC/60Hz

AUTO SAFETY SHUT-OFF WITH CERAMIC

CONTROL

This heater is equipped with a patented, technologically

advanced, safety system that requires the user to reset the

heater if there is a potential overheat situation. When a

potential overheat temperature is reached, the system will

automatically shut the heater off. It can only resume

operation when the user resets the unit. For specific reset

instructions please refer to the unit.

To Reset the Heater

If the unit shuts down:

1. Unplug unit.

2. Wait 10 minutes for unit to cool down.

3. Plug in and operate normally.

NOTE: To shut unit OFF, hold Mode/Off button down for 2

seconds.

PRE-OPERATING INSTRUCTIONS

1. Carefully remove your heater from the box. Please

save the carton for off-season storage.

2. Place heater on firm level surface.

3. Avoid overloading your circuit by not using other high

wattage appliances in the same outlet. At 1500 Watts,

this unit draws 12.5 Amps.

OPERATING INSTRUCTIONS

Your heater is equipped with a technologically advanced

1Touch®electronic thermostat. You can set the heater to

run continuously in manual mode or set the 1Touch®

thermostat to your desired temperature setting. The

1Touch®thermostat will automatically turn the heater ON

or OFF depending on the preset comfort level. The comfort

level ranges between 60°F and 80°F.

PLEASE READ AND SAVE THESEIMPORTANT SAFETY INSTRUCTIONS FEATURES - OPERATIONS

Thank you for purchasing this Holmes®product. We understand

the value of quality and are committed to making superior

products that stand the test of time. We trust this product

will exceed your expectations of quality and reliability. We

hope that you enjoy this product and will consider purchasing

another Holmes®product in the future.

To see our full product line or if you have any questions or

comments about this product, please visit our website at:

www.holmesproducts.com.

When using electrical appliances, basic safety precautions

should always be followed to reduce the risk of fire, electric

shock, and injury to persons, including the following:

1. Read all instructions before using the appliance.

2. To avoid fire or shock hazard, plug the appliance

directly into a 120V AC electrical outlet.

3. The heater is hot when in use. To avoid burns, DO NOT

let bare skin touch hot surfaces. If provided, use handles

when moving this heater. Keep combustible materials,

such as furniture, pillows, bedding, papers, clothes, and

curtains at least 3 ft (0.9 m) from the front of the

heater and keep them away from the sides and rear.

4. DO NOT run cord under carpeting. DO NOT cover cord

with throw rugs, runners, or the like. Arrange cord away

from traffic area and where it will not be tripped over.

5. This heater is not intended for use in bathrooms, laundry

areas and similar indoor location. NEVER locate heater

where it may fall into a bathtub or other water container.

6. Extreme caution is necessary when any heater is used

by, or near children or invalids, and whenever the

heater is left operating and unattended.

7. Always unplug the heater when not in use.

8. When unplugging, be sure to pull by the plug and not

the cord.

9. DO NOT insert or allow foreign objects to enter any

ventilation or exhaust opening as this may cause an

electric shock or fire, or damage the heater.

10. DO NOT operate heater with a damaged cord or plug,

or after the heater malfunctions, has been dropped or

damaged in any manner. Return appliance to

manufacturer for examination, electrical or mechanical

adjustment, or repair.

11. A heater has hot and arcing or sparking parts inside.

DO NOT use it in areas where gasoline, paint, or

flammable liquids are used or stored.

12. Use appliance only for intended household use as

described in this manual. Any other use not recommended

by the manufacturer may cause fire, electric shock, or

injury to persons. The use of attachments not

recommended or sold by the manufacturer cause hazards.

13. DO NOT use outdoors.

14. To prevent a possible fire, DO NOT block air intakes or

exhaust in any manner. DO NOT use on soft surfaces,

like a bed, where openings may become blocked.

15. To disconnect heater, turn controls to OFF, then remove

plug from outlet.

16. Avoid the use of an extension cord because the extension

cord may overheat and cause a risk of fire. However,

if you have to use an extension cord, the cord shall be

No. 14 AWG minimum size and rated not less than

1875 watts.

17. If the heater will not operate, see specific instructions

on Auto Safety Shut-off.

Manual Mode Instructions:

1. Plug the heater into a 120V AC electrical outlet.

2. To start the unit, push the MODE/OFF button once for

the HIGH (HI) manual setting. (See Figure 1 and 2)

3. Press the button again for the LOW (LO) manual

setting. (See Figure 1 and 2)

4. To stop the unit, press and hold the button for two

seconds or keep pressing the button until all the

temperature indicators are OFF.

NOTE: The Power Light will remain lit as long as unit is

plugged in.

1TOUCH®THERMOSTAT INSTRUCTIONS

To take advantage of the 1Touch®Thermostat continue to

press the MODE/OFF button until the desired temperature

is set in either the HIGH or LOW setting. When ambient

temperature rises above the set temperature, the heater

will stop. When the ambient temperature drops below the

set temperature, the heater will turn on automatically.

NOTE: When the 1Touch®thermostat is set, either the HIGH

or LOW power light, and the set temperature light will

remain lit during operation. (See Figure 1 and 2)

NOTE: It is normal for the heater to cycle ON and OFF as

it maintains the preset temperature. To prevent the unit

from cycling, you need to raise the thermostat setting.

NOTE: 1Touch®has memory. The 1Touch®thermostat will

remember the previous temperature setting after the unit

has been turned off. However, if the unit is unplugged, or

the unit is turned off at low power - 80˚F setting, the

1Touch®thermostat will be reset and will no longer remember

the previous temperature setting.

CLEANING/MAINTENANCE

• Always unplug the heater before cleaning.

• Lightly run a vacuum cleaner nozzle over the heater grill

to remove any dust or dirt that may have accumulated.

• Carefully wipe the heater with a soft, damp cloth. Please

be very cautious near the motor and heating elements.

• NEVER use abrasive or flammable solvents to clean

the heater.

• After cleaning, be sure to completely dry the heater

with a cloth or towel.

• Store your heater in its original carton in a cool, dry

location.

TROUBLESHOOTING

If your heater fails to operate, unplug the

heater and:

• Make sure the electrical outlet and circuit breaker are

working.

• Check for obstructions. If you find an obstruction, turn

OFF and UNPLUG the heater. Carefully remove the

obstruction and follow the reset instructions.

• Make sure the Mode Control is on the Lo or Hi setting.

Please DO NOT attempt to open or repair the heater.

Please see the Warranty for Service Instructions or

call our Consumer Service Department at

1-800-546-5637.

FEATURES - OPERATIONSCLEANING / MAINTENANCE

A. 1Touch®Mode/Off Button

B. Carry Handle (Not Visible)

C. Temperature Set Lights

D. HI/LO Power Lights

E. Power Light

Figure 2

A. 1Touch®Mode/Off Button

B. Temperature Set Lights

C. HI/LO Power Lights

D. Power Light

Figure 1

THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the

other). To reduce the risk of electric shock, this plug is intended to fit in

a polarized outlet only one way. If the plug does not fit fully in the

outlet, reverse the plug. If it still does not fit, contact a qualified

electrician to install the proper outlet.

DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS

SAFETY FEATURE IN ANY WAY.

HFH298607EM1.qxd 3/20/07 9:21 AM Page 2