P L E A S E R E A D A N D S AV E T H E S E
I M P O R TA N T S A F E T Y I N S T R U C T I O N S
F E AT U R E S - O P E R AT I O N S
F E AT U R E S - O P E R AT I O N S
When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:
1.Read all instructions before using the appliance.
2.To avoid fire or shock hazard, plug the appliance directly into a 120V AC electrical outlet.
3.The heater is hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 ft (0.9
m)from the front of the heater and keep them away from the sides and rear.
4.DO NOT run cord under carpeting. DO NOT cover cord with throw rugs, runners, or the like. Arrange cord away from traffic area and where it will not be tripped over.
5.This heater is not intended for use in bathrooms, laundry areas and similar indoor location. NEVER locate heater where it may fall into a bathtub or other water container.
6.Extreme caution is necessary when any heater is used by, or near children or invalids, and whenever the heater is left operating and unattended.
7.Always unplug the heater when not in use.
8.When unplugging, be sure to pull by the plug and not the cord.
9.DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
10.DO NOT operate heater with a damaged cord or plug, or after the heater malfunctions, has been dropped or damaged in any manner. Return appliance to manufacturer for examination, electrical or mechanical adjustment, or repair.
11.A heater has hot and arcing or sparking parts inside. DO NOT use it in areas where gasoline, paint, or flammable liquids are used or stored.
12.Use appliance only for intended household use as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons. The use of attachments not recommended or sold by The Holmes Group may cause hazards.
13.DO NOT use outdoors.
14.To prevent a possible fire, DO NOT block air intakes or exhaust in any manner. DO NOT use on soft surfaces, like a bed, where openings may become blocked.
15.To disconnect heater, turn controls to OFF, then remove plug from outlet.
16.Avoid the use of an extension cord because the extension cord may overheat and cause a risk of fire. However, if you have to use an extension cord, the cord shall be No.14 AWG minimum size and rated not less than 1875 watts.
17.If the heater will not operate, see specific instructions on Auto Safety
18.DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit. Doing so will void your warranty. The inside of the unit contains no user serviceable parts. All servicing should be performed by qualified personnel only.
19.Discontinue use if plug or outlet is hot. It is recommended that the outlet be replaced if plug or outlet is hot to touch.
PLEASE READ AND SAVETHESE IMPORTANT
SAFETY INSTRUCTIONSTECHNICAL SPECIFICATIONS
•Wattage: 1500W (+5%
•Working Voltage: 120V AC/60Hz
AUTO SAFETY SHUT-OFF WITH MANUAL RESET
This heater is equipped with a patented,
To Reset the Heater:
PRE-OPERATING INSTRUCTIONS
1.Carefully remove your heater from the box. Please save the carton for
2.Make sure the unit is in the OFF position before plugging the heater into the outlet.
3.Place heater on firm level surface.
4.Avoid overloading your circuit by not using other high wattage appliances in the same outlet. At 1500 watts, this unit draws 12.5 Amps.
NOTE: The power light will remain lit while the heater is plugged in.
| Figure 1 | HFH6402 Control Panel |
| OSCILLATION BUTTON TEMP/TIMER UP BUTTON |
| MODE BUTTON |
|
| TEMP/TIMER DOWN BUTTON |
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Figure 2 | HFH6408 Control Panel | |||||||
|
|
|
|
|
|
|
| |
|
| MODE BUTTON |
|
|
|
|
| |
|
|
|
| TEMP/TIMER UP BUTTON | ||||
AccuTemp Plus™ DIGITAL THERMOSTAT
Your heater is equipped with an AccuTemp Plus™ Digital Thermostat that allows you to set your heater to your precise comfort level.
Setting the AccuTemp Plus™ thermostat:
1.Press the Mode Button once for manual HI power. The heater will run continuously on HI.
2.Press the Mode Button again for manual LO power. The heater will run continuously on LO.
3.Press the Mode Button for a third time for Auto Mode HI Power (AH) or press again for Auto Mode LO Power (AL). In either of these modes you may then press the up, and down buttons to reach your desired temperature.
4.Once you have reached your desired temperature, the display will return to current room temperature and gradually increase until the room has reached the preset temperature.
5.If the unit will not start in the AccuTemp Plus™ mode, please make sure the “set temperature” is higher than the current room temperature.
NOTE: It is normal for the heater to cycle ON and OFF as it maintains the preset temperature. To prevent the unit from cycling, you need to raise the thermostat setting. When the preset temperature is reached, the fan will run for 30 seconds without heat. This cool down process ensures an accurate and consistent temperature reading. If you unplug the heater, you will have to reset the AccuTemp Plus™ thermostat again by following the above instructions.
NOTE: To shut the unit off at any time, press and hold the mode button down for two seconds. For 6408 only, after heater is turned off, fan will run for 30 seconds to cool unit.
NOTE: AccuTemp Plus™ has memory. The AccuTemp Plus™ thermostat will remember the previous temperature setting after the unit has been turned off. However, if the unit is unplugged, the AccuTemp Plus™ thermostat will be reset and will no longer remember the previous temperature setting.
USING THE PROGRAMMABLE TIMER
AccuTemp Plus™ allows the user to program the heater to turn on at a preset time, or turn off after a set amount of time.
Setting the Off Timer:
1.Select the Mode and or temperature you wish the heater to run in.
2.While the heater is running, press and hold the up and down buttons simultaneously.
3.By pressing the up and down buttons, program the heater to turn off up to 16 hours from the current time in increments of 1 hour.
4.After setting the timer, the LED display will return to show the current room temperature. For HFH6408 only, a LED will illuminate to show that the timer is activated.
5.After the predetermined length of time has passed, the heater will automatically shut off.
Setting the On Timer:
1.While the heater is off, press and hold the up and down buttons simultaneously.
2.By pressing the up and down buttons, program the heater to turn on up to 16 hours in advance of current time in increments of 1 hour.
3.After the preset length of time has passed, the heater will automatically turn on at the last mode setting that was programmed. If no program was set, the heater will turn on Auto Mode HI Power at 75° for a preset time of 2 hours.
OSCILLATION INSTRUCTIONS
1.Select the desired control setting and press or switch the oscillation button to the ON position.
2.To stop oscillation, press or switch the oscillation button to OFF.
3.Please do not manually turn the unit; it is designed to turn only by motorized oscillation.
REMOTE CONTROL INSTRUCTIONS (For HFH6408 only)
The remote control for this unit has the capability of controlling every function from a distance. Please note this remote control will not work through walls.
Figure 3
Insert 2 "AAA" batteries (not included) into the remote control. POWER: To turn the unit on or off press the Power button.
MODES: To scroll through the various modes OF, HI, LO, AH and AL press the Mode button until you reach your desired setting.
OSCILLATION: To start oscillation, press the OSC. button once. To stop oscillation press the button again.
TO INCREASE OR DECREASE TEMPERATURE: To increase the temperature setting that you desire press the upward facing triangle marked Temp Up. To decrease the temperature setting that you desire press the downward facing triangle marked Temp Down.
TIMER: To activate the timer from the remote control, press the Temp Up and Temp Down buttons at the same time. This will give you the ability to have your heater program to turn on or off in 1 hour increments up to 16 hours. For more information see the Programmable Timer instructions above.
BATTERY WARNING:
•DO NOT mix old and new batteries.
•DO NOT mix alkaline, standard
THIS PRODUCT IS EQUIPPED WITH A POLARIZED AC (Alternating Current) PLUG (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact qualified personnel to install the proper outlet.
DO NOT DEFEAT THE SAFETY PURPOSE OF THIS
POLARIZED PLUG IN ANY WAY
1.Unplug the heater and wait 10 minutes for the unit to cool down.
2.After the 10 minutes, plug the unit in again and operate normally.
Tip-Over Shut-Off:
When the unit is accidentally knocked over, it will instantly shut off. To reset, simply place the heater in an upright position. Press the MODE button and operate normally.
OSCILLATION BUTTON | TEMP/TIMER DOWN BUTTON |
